User manual DENON AVR-1913

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. · DECLARATION DE CONFORMITE Nous déclarons sous notre seule responsabilité que l'appareil, auquel se réfère cette déclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. D'après les dispositions de la Directive 2006/95/EC et 2004/108/EC. Um dieses Gerät vollständig von der Stromversorgung abzutrennen, ziehen Sie bitte den Stecker aus der Wandsteckdose. Der Netzstecker wird verwendet, um die Stromversorgung zum Gerät völlig zu unterbrechen; er muss für den Benutzer gut und einfach zu erreichen sein. PRECAUTION: · DICHIARAZIONE DI CONFORMITÀ Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. [. . . ] : Select this when no subwoofer is connected. [Selectable items] LFE (Normal) : Play low range and LFE signal of channels set to "Small" . LFE+Main : Play low range and LFE signal of all channels. 1spkr : Select the number of surround back speakers. · This can be set when "System Setup" ­ "Speaker Setup" ­ "Subwoofer" is set to "Yes" . · Play music or a movie source and select the mode offering the strongest bass. · Select "LFE+Main" if you want the bass signals to always be produced from the subwoofer. Operations (vpage 21) ENGLISH A6 Crossover Frequency Select crossover frequency from which subwoofer handles low range signal. A7 Test Tone Adjust channel levels to obtain equal volume from all speakers. Operating from the remote control unit Adjusting with the remote control unit using the test tones is only possible in the "Auto" mode and only effective in the STANDARD mode. The adjusted levels for the different modes are automatically stored in the memory. GAdjusting using test tonesH q Press the TEST button on the remote control unit. Test tones are output from the various speakers. w Use the o p button to adjust so that the volume is equal for all speakers. e When the adjustments are completed, press the TEST button on the remote control unit again. Getting Started [Display] 1. Sp 2. In 3. Op Q [Display] 1. Sp 2. In 3. Op Q Connections Speaker Setup Q Q Speaker Setup 17 T. Tone T. Tone Yes< 16Cr. Over 80Hz Auto > Setup Q Q [Selectable items] 40Hz 200Hz 60Hz 250Hz : 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz Playback Test Tone On Q Auto-FL Only the portion of the bass sound of the various speakers output from the subwoofer that has a frequency below the frequency set here is output. Set this according to the low frequency reproduction capabilities of the speakers you are using. Test Tone Select test tone playback method. [Selectable items] Auto : Automatically switch speaker from which test tone is output. · When "System Setup" ­ "Speaker Setup" ­ "Surround Back Speaker" setting (vpage 22) is set to "1spkr" the surround back , speaker display is set to "SB" . · Speakers set to "None" in the Speaker Configuration settings are not displayed. · When "Test Tone" is adjusted, the adjusted values are set for all the surround modes. : Make separate settings for 2-channel mode. Option Setup E ­40dB : The sound is attenuated by 40 dB. ­20dB : The sound is attenuated by 20 dB. z: Use the same settings as in "Speaker Setup" . 2 Limit 3 P. On 4 Mute OFF E Front Select front speaker size. LAST E g ~ A1 2ch Direct/Stereo Custom Make speaker settings for 2-channel mode playback. [Selectable items] Large Small : Select front speaker size. FULL [Display] Volume Limit Make a setting for maximum volume. Subwoofer Select subwoofer use. E 1. Sp 2. In 3. Op Option Setup E [Selectable items] OFF : Do not set a maximum volume. [Selectable items] Yes No : Select subwoofer use. 5 2ch Cstm 5 2ch Cstm 6 2ch F 7 2ch SW OFF E ­20dB : Set the maximum volume to ­20 dB. ­10dB : Set the maximum volume to ­10 dB. 0dB : Set the maximum volume to 0 dB. ON E Subwoofer Mode Select low range signal to be reproduced by subwoofer. Large E [Selectable items] LFE (Normal) LFE+Main : Select subwoofer signal. Power On Level This sets the volume set when the main zone's power is turned on. Yes E [Selectable items] Last ­­­ : Use the memorized setting from the last session. : Always use the muting on condition when power is turned on. in units of 1 dB. 8 2ch LFE 9 2ch FL 10 2ch FR 11 2ch Freq Norm E Distance FL Set distance from listening position to front left speaker. 3. 6m E 3. 6m E [Variable range] 0. 0m ~ 18. 0m ­80dB ~ +18dB : Set the volume level when the power is turned on 80 Operations (vpage 21) ENGLISH Distance FR Set distance from listening position to front right speaker. A3 Room EQ Setup Select room EQ setting method. A5 Remote ID Setup Set remote control ID. Getting Started [Variable range] 0. 0m ~ 18. 0m [Display] 1. Sp 2. In 3. Op E [Display] 1. Sp 2. In 3. Op E Crossover Select crossover frequency from which subwoofer handles low range signal. Connections Option Setup E Option Setup E [Selectable items] 40Hz 200Hz 60Hz 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz 250Hz : Select crossover frequency. [Selectable items] All 13 EQ All 15 Remote ID 1 Setup [Selectable items] NOTE 1 2 3 4 : Apply settings to all surround modes. When using the AVR-1913 with only the included remote control unit (RC-1076), there is no need to make settings. When using a separately sold remote control unit (RC-7000CI, etc. ), this function can be used. Match the ID setting of the remote control unit and the receiver. Playback Assign : Make settings for each surround mode separately. A2 Auto Surround Mode Make setting for memorizing surround mode setting for each input signal type. Remote Control A4 Direct Mode Setup Select room EQ use for DIRECT mode. [Display] 1. Sp 2. In 3. Op E [Display] 1. Sp 2. In 3. Op E E Amp Assign Option Setup 12AutoSurr. ON Option Setup E Information [Selectable items] ON OFF : Memorize settings. [. . . ] · Subwoofer's power not turned on. · The "Subwoofer" setting at "Speaker Configuration" is set to "No" . · The subwoofer is not properly connected. · The subwoofer's volume is turned off. [. . . ]