User manual DENON AVR-2106

[. . . ] AV SURROUND RECEIVER AVR-2106 OPERATING INSTRUCTIONS ENGLISH 2 SAFETY PRECAUTIONS SAFETY INSTRUCTIONS 1. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. [. . . ] OFF ´ ­12 dB ´ +12 dB Press the TONE DEFEAT button. The signals do not pass through the bass and treble adjustment circuits, thus resulting in higher quality sound. 29 ENGLISH ENGLISH Basic Operation Basic Operation FUNCTION BAND PRESET · Auto tuning TUNER TUNING 1 2 3 Set the input source to "TUNER". MODE BAND (Main unit) (Remote control unit) ON/STANDBY POWER TUNING Watching the display, press the BAND button to select the desired band (AM or FM). Press the MODE button to set the auto tuning mode. Listening to the radio Auto preset memory · This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. · The "Auto tuner preset" operation can also be performed at "System setup" ( page 44). 2 DEFAULT SETTINGS Auto tuner presets 87. 5 / 89. 1 / 98. 1 / 107. 9 / 90. 1 / 90. 1 / 90. 1 / 90. 1 MHz 520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90. 1 / 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz A1 ~ A8 B1 ~ B8 C1 D1 E1 F1 G1 ~ ~ ~ ~ ~ C8 D8 E8 F8 G8 Hold the PRESET · button and press the POWER switch on the main unit. · The unit automatically begins searching for FM broadcast stations. When the first FM broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations are automatically stored in order at preset channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to F8 and G1 to G8 for a maximum of 56 stations. Channel A1 is tuned in after the auto preset memory operation is completed. 4 Press the TUNING (+) or (­) button. Automatic searching begins, then stops when a station is tuned in. · When in the auto tuning mode on the FM band, the "STEREO" indicator lights on the display when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "STEREO" indicators turn off. · If an FM station cannot be preset automatically due to poor reception, use the "Manual tuning" operation to tune in the station, then preset it using the manual "Preset memory" operation. · To interrupt this function, press the ON/STANDBY switch. 30 ENGLISH ENGLISH Basic Operation Basic Operation FUNCTION BAND PRESET STATUS Checking the preset stations TUNER BAND MEMORY MODE ON SCREEN TUNING PRESET SHIFT The preset (broadcast) stations can be checked on the on screen display. Press the ON SCREEN button repeatedly until the "Tuner Preset Stations" screen appears on the OSD. ON/STANDBY SHIFT POWER TUNING Manual tuning Preset stations 1 2 3 4 Set the input source to "TUNER". 1 2 3 4 5 Use the "Auto tuning" or "Manual tuning" operation to tune in the station to be preset in the memory. Press the MEMORY button. Recalling preset stations Watching the display, press the BAND button to select the desired band (AM or FM). Press the MODE button to set the manual tuning mode. Press the SHIFT button and select the desired memory block (A to G). Press the PRESET (+) or (­) button to select the desired preset channel (1 to 8). Press the MEMORY button again. · Store the station in the preset memory. 1 2 Watching the display, press the SHIFT button to select the preset memory block. Watching the display, press the PRESET · (+) or ª (­) button to select the desired preset channel. Check that the display's "AUTO" indicator turns off. Press the TUNING (+) or (­) button to tune in the desired station. The frequency changes continuously when the button is held in. · When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the "STEREO" indicator turns off. · To preset other channels, repeat steps 1 to 4. A total of 56 broadcast stations can be preset -- 8 stations (channels 1 to 8) in each of blocks A to G. 31 ENGLISH ENGLISH Basic Operation Basic Operation XM Satellite Radio 2 Introducing XM Satellite Radio There's a world of audio listening pleasure beyond AM and FM. Select from over 150 channels of music, news, sports, comedy, talk, and entertainment. With all music channels 100% commercial free. Checking the XM signal strength and Radio ID Channel selection Questions?: Visit www. xmradio. com. 2 How to subscribe Listeners can subscribe by visiting XM on the Web at www. xmradio. com or by calling XM's Listener Care at (800) 9672346. Customers should have their Radio ID and credit card ready. The Radio ID can be found by selecting channel 0 on the radio. 1 2 3 Set the input source to "TUNER". Watching the display, press the BAND button to select the XM mode. Press the STATUS button until "SIGNAL" is displayed. · The display changes as shown below according to the receiving condition. Display GOOD MARGINAL WEAK NO Condition Signal strength is good Signal strength is marginal Signal strength is poor Loss of the signal 1 2 3 Set the input source to "TUNER". Watching the display, press the BAND button to select the XM mode. Press the TUNING (+) or (­) button to reach the desired channel. XM040 DeepTrks Channel number Channel name 2 A warning against reverse engineering It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE® voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. [. . . ] What's more, DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 signal sources can be played with a sampling frequency of 48 kHz or 44. 1 kHz on conventional DTS or DTS-ES surround decoders ( 2). 1 A DVD player with DTS digital output capabilities (for CD/LD players, a player with digital outputs for conventional DTS CDs/LDs) and a disc recorded in DTS 96/24 are required. 2 The resolution is 24 or 20 bits, depending on the decoder. 2 DTS Neo:6TM surround This mode applies conventional 2-channel signals to the high precision digital matrix decoder used for DTS-ES Matrix 6. 1 to achieve 6. 1-channel surround playback. High precision input signal detection and matrix processing enable full band reproduction (frequency response of 20 Hz to 20 kHz or greater) for all 6. 1 channels, and separation between the different channels is improved to the same level as that of a digital discrete system. [. . . ]