User manual DENON AVR-5800-B

[. . . ] AV SURROUND RECEIVER AVR-5800 OPERATING INSTRUCTIONS MASTER VOLUME INPUT SELECTOR VOLUME LEVEL REMOTE SENSOR INPUTSIGNAL LOCK DIGITAL AL24 SURROUND BACK CH OUTPUT AUTO INPUT MODE PCM DTS RF SIGNAL DETECT ¥)) ON / STANDBY HOME THX CINEMA PURE DIRECT SURROUND SPEAKER A B PHONO CD TUNER DVD VDP TV DBS / SAT VCR-1 VCR-2 VCR-3 V. AUX CDR / TAPE-1 MD / TAPE-2 SURROUND MODE DIRECT PHONES STEREO DOLBY SURROUND DTS SURROUND WIDE SCREEN 5CH / 7CH STEREO DSP SIMULATION STATUS MODE SELECT MULTI FUNCTION FUNCTION CONTROL INPUT MODE ANALOG EXT. IN CINEMA / MUSIC 6. 1 / 7. 1 SURROUND VIDEO ON / OFF TONE DEFEAT M-ZONE 1 REC / M-ZONE 2 INPUT REC SELECT / M-ZONE PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-5800 2 We greatly appreciate your purchase of the AVR-5800. 2 To be sure you take maximum advantage of all the features the AVR-5800 has to offer, read these instructions carefully and use the set properly. [. . . ] NOTE: To prevent hearing loss, do not raise the volume level excessively when using headphones. On screen display · Each time an operation is performed, a description of that operation appears on the display connected to the unit's VIDEO MONITOR OUT jack. Also, the unit's operating status can be checked during playback by pressing the remote control unit's ON SCREEN button. Such information as the position of the input selector and the surround parameter settings is output in sequence. Front panel display · Descriptions of the unit's operations are also displayed on the front panel display. In addition, the display can be switched to check the unit's operating status while playing a source by pressing the STATUS button. (Remote control unit) STATUS (Main unit) [3] Turning the sound off temporarily (muting) 1 Using the dimmer function · Use this to change the brightness of the display. The display brightness changes in four steps (bright, medium, dim and off) by pressing the remote control unit's DIMMER button repeatedly. The brightness changes in 3 steps each time the button is pressed, and finally the display turns off. (Remote control unit) 1 Use this to turn off the audio output temporarily. Press the MUTE button again. [6] Switching the surround speakers (Remote control unit) [4] Combining the currently playing sound with the desired image 1 1 1 The surround speakers switch as shown below each time the SPEAKER button is pressed. SURROUND A SURROUND B (Remote control unit) 1 Simulcast playback Use this switch to monitor a video source other than the audio source. Press the remote control unit's VIDEO SELECT button until the desired image appears. (Remote control unit) Cancelling simulcast playback. · Select "SOURCE" using the video select button. · Switch the program source to the component connected to the video input. SURROUND A+B This operation is possible when the setting for using both surround speakers A and B is made at "Speaker Configuration" in the System Setup Menu. 35 Multi-source recording/playback With the exception of the case in [2] below, only the signal connected to the analog input jacks are output from the REC OUT and multi-room output jacks. [1] Playing one source while recording another (REC OUT mode) 1 2 3 4 Press the REC/M-ZONE 2 button until "REC OUT SOURCE" appears on the set's display. REC / M-ZONE 2 (Main unit) Select the source you want to record appears on the set's display. · The indicator for the selected program source lights. FUNCTION 1, 2 (Main unit) 1, 4 2 2 Display Set the recording mode. · For operating instructions, refer to the manual of the component on which you want to record. To cancel, press the REC/M-ZONE 2 button twice. PHONO CD TUNER AUX DVD / VCR -1 -2 V. AUX MD / VDP TV / DBS TAPE -1 -2 REC / M-ZONE 2 (Main unit) NOTES: · Recording sources other than digital inputs selected in the REC OUT mode are also output to the multi source audio/video output jacks. · Digital signals are not output from the MULTI ZONE 1 audio output jacks. [2] Recording Dolby Digital and DTS multichannel sources · With this set it is possible to record Dolby Digital and DTS multichannel signals converted into 2-channel analog signals. · The recording signals are output to the MULTI ZONE-2 OUT, TAPE and VCR output terminals. 1 2 3 Press the REC/M-ZONE 2 button until "REC OUT SOURCE" appears on the display. REC / M-ZONE 2 (Main unit) Set the input mode according to the source to be played. INPUT MODE (Main unit) Set the surround mode by pressing the DIRECT or STEREO button. · The multichannel digital signals are down-mixed and output to the TAPE and VCR output terminals. STEREO 3 3 or or (Main unit) (Remote control unit) 4 36 Set the recording mode. [3] Outputting a program source to an amplifier, etc. , in a different room (M-ZONE 1 mode) 1 2 3 1 2 Press the M-ZONE 1 button. M-ZONE 1 (Main unit) Select the source you want to output appears on the set's display. FUNCTION (Main unit) Start playing the source to be output. · For operating instructions, refer to the manuals of the respective components. [4] Outputting a program source to an amplifier, etc. , in a different room (M-ZONE 2) Press the REC/M-ZONE 2 button until "M-ZONE 2 SOURCE" appears on the set's display. REC / M-ZONE 2 (Main unit) Select the source you want to record appears on the set's display. · The indicator for the selected program source light. · When the AVR-5800 is in the REC OUT mode, the source cannot be output using the M-ZONE 2 buttons on the remote control unit. FUNCTION 1, 2 (Main unit) 1 2 2 Display PHONO CD TUNER AUX DVD / VCR -1 -2 V. AUX MD / VDP TV / DBS TAPE -1 -2 3 Start playing the source to be output. [. . . ] Upon playback, the signals are decoded by a high precision digital matrix decoder within the Dolby Digital decoder into the SL, SR and SB channels and output as 6. 1 channels of signals. With the AVR-5800, the signals further undergo Home THX Cinema processing to achieve a THX Surround EX system. Even without the proper environment for playing the SB channel, Dolby Digital Surround EX signals are 100% compatible with existing 5. 1-channel playback systems, so they can be played as such. In this case, the SB channel signal is produced as a monaural signal from both the SL and SR channels, so none of the signal components are missing. [. . . ]