User manual DENON DRA-F101

[. . . ] STEREO RECEIVER DRA-F101 OPERATING INSTRUCTIONS MODE D'EMPLOI INSTRUCCIONES DE OPERACION OFF SYSTEM POWER ON PROG / DIRECT 1 4 2 5 3 CALL 6 CLEAR 7 8 9 RANDOM REPEAT 10 +10 CD SRS TAPE MD TIME EDIT DIMMER TIME/ PANEL RDS BAND TUNING STOP PLAY VOLUME /SELECT VOLUME FUNCTION TONE TIMER DISPLAY MEMORY / SET TUNING DOWN UP BAND SOURCE DIRECT PRESET + TAPE SLEEP FUNCTION MODE SYSTEM ON / STANDBY PHONES TUNER CD MD TAPE AM-FM STEREO RECEIVER DRA-F101 RC-927 REMOTE CONTROL UNIT FOR ENGLISH READERS POUR LES LECTEURS FRANCAIS PARA LECTORES DE ESPAÑOL PAGE 004 ~ PAGE 019 PAGE 020 ~ PAGE 035 PAGINA 036 ~ PAGINA 051 IMPORTANT TO SAFETY WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE: This stereo receiver uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is recommended to use this in a room of 5°C (41°F) -- 35°C (95°F). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] (This operation is only possible from the remote control unit (RC-927). ) NOTE: If a several timer operations are set at once, the sleep timer has priority. Press the SLEEP button. 1 Press the SLEEP button again while the "SLEEP" indicator is flashing. 2 3 The previous display reappears after 5 seconds. The "SLEEP" indicator remains lit, indicating that the sleep timer is functioning. · The time is reset to "60" (60 minutes) if the SLEEP button is pressed again while the sleep timer is functioning. 17 ENGLISH 11 TROUBLESHOOTING Check the following before assuming there is a problem with the set. Is the set being operated as described in the operating instructions ?Are the speakers and input components being operated properly ?If the set does not seem to be operating properly, check the points listed below. If these points do not apply, the set may be damaged. Turn off the power immediately and contact your store of purchase. Symptom POWER LED does not light and no sound is produced when POWER switch is turned on. Cause · Power supply cord is not connected. Remedy · Check that the cord is plugged in. page 6, 8, 12 Symptom Cause · Turntable's ground wire not connected. · Input cords not properly connected to PHONO terminals. · Influence from a TV or other electrical device near the turntable. · Turntable and speaker systems are too close. · Floor is soft and vibrates easily. Remedy · Connect securely. · Change the position of installation. · Move speaker systems as far away as possible. · Use cushions to absorb the vibrations transmitted from the floor to the speakers. If the turntable does not include insulators, use audio insulators, available in stores. · Insert batteries properly. page 6 6 -- -- -- Booming sound produced when playing records. · Speaker cords not properly connected. · INPUT SELECTOR not set to proper position. · Speaker cords not properly connected. · Input cords not properly connected. · Left/right balance improperly adjusted. · Left and right speakers or input cords inverted. [. . . ] · Ajuste el interruptor a la posición correcta. · Ajuste el control a un nivel apropiado. · Elija otro lugar de instalación. -- 38 44 44 38 38 45 Distorsión del sonido. Se produce ruido tipo aullido al aumentar el nivel de volumen durante la reproducción de discos. El LED POWER se enciende, pero no hay emisión de sonido. · Conecte los cables en forma segura. · Conecte los cables en forma segura. [. . . ]