User manual DENON POA-T2

[. . . ] Follow Instructions ­ All operating and use instructions should be followed. Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. [. . . ] DTS (exclusive DTS signal playback mode): Decoding and playback are only performed when DTS signals are being input. Combining the currently playing sound with the desired image (VIDEO SELECT) Press the VIDEO SELECT button repeatedly until the desired source appears on the display. Checking the currently playing program source 2 Front panel display Press the STATUS button. Descriptions of the unit's operations are also displayed on the front panel display. In addition, the display can be switched to check the unit's operating status while playing a source. IN=V SOURCE Use this switch to monitor a video source other than the audio source. 2 Using the dimmer function · Canceling simulcast playback: q Select "SOURCE" by pressing the VIDEO SELECT button. w Switch the program source to the component connected to the video input terminals. Press the DIMMER button. The display brightness changes in four steps (bright, medium, dim and off). 19 ENGLISH ENGLISH Basic Operation Basic Operation 2 Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG (exclusive analog audio signal playback mode): The signals input to the analog input terminals are decoded and played. NOTE: · Input mode when playing DTS sources: Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input terminals (OPTICAL/COAXIAL) and set the input mode to "DTS". 2 Input signal display · DOLBY DIGITAL NOTE: · The "DIGITAL" indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard. · DTS · PCM The "DIGITAL" indicator lights when digital signals are being input properly. If the "DIGITAL" indicator does not light, check whether the Digital In Assignment setup ( page 16) and connections are correct and whether the component's power is turned on. 2 Input mode display · In the AUTO mode Depending on the input signal. Surround Playing audio sources (CDs and DVDs) 2-channel playback modes · The POA-T2 is equipped with 2-channel playback modes exclusively for music. · Select the mode to suit your tastes. 2 STEREO mode Use this mode to adjust the tone and achieve the desired sound while watching images. · In the DIGITAL PCM mode 2 DIRECT mode Use this mode to achieve good quality 2-channel sound while watching images. In this mode, the audio signals bypass such circuits as the tone circuit and are transmitted directly, resulting in good quality sound. Press the DIRECT/STEREO button on the main unit or the STEREO button on the remote control unit to select the STEREO mode. · In the DIGITAL DTS mode · In the ANALOG mode Press the DIRECT/STEREO button on the main unit or the DIRECT button on the remote control unit to select the DIRECT mode. 20 ENGLISH ENGLISH Basic Operation Basic Operation STANDARD STANDARD 5 SURROUND PARAMETER CURSOR G Press the SURROUND PARAMETER button to select the various parameters. The mode switches as shown below each time the button is pressed. ENTER CURSOR F · When the Cinema mode: MODE CINEMA DEFAULT CINEMA EQ TONE DEFEAT SURROUND BACK SURROUND PARAMETER SELECT · When the Music mode: MODE MUSIC DEFAULT TONE DEFEAT SURROUND BACK PANORAMA CENTER WIDTH DIMENSION · When the Game mode: Dolby Pro Logic IIx (Pro Logic II) mode · To play in the PLIIx mode, set "S. BackSp" at the "Speaker Configuration" setting to "1sp" or "2sp". · To play in the PLIIx mode, set "Surround Back" at the "Power Amp Assign. " setting. MODE GAME TONE DEFEAT 4 Turn the SELECT knob, and press the CURSOR F or G button to select the optimum mode for the source. DEFAULT SURROUND BACK · When the Dolby Pro Logic mode: MODE DOLBY PL CINEMA EQ TONE DEFEAT When the "SURROUND BACK" parameter is set to "ON". Back" at system setup to "Small" or "Large". ) (Pro Logic IIx Cinema mode) (Pro Logic IIx Music mode) DEFAULT SURROUND BACK 1 Press the STANDARD button to select the Dolby Pro Logic IIx mode. · The Dolby Pro Logic II indicator lights. Lights If you do want the bass and treble to be adjusted, turn off the tone defeat mode. (Pro Logic IIx Game mode) The mode switches as shown below each time the button is pressed. DOLBY PLIIx DTS NEO:6 6 Turn the SELECT knob, and press the CURSOR F or G button to set the various surround parameters. When the "SURROUND BACK" parameter is set to "OFF". The settings are automatically finalized and the normal display reappears after several seconds. 7 Press the ENTER button to finish the surround parameter mode. 23 ENGLISH ENGLISH Basic Operation Basic Operation · When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and the setting will be completed. 2 Surround parameters w DTS NEO:6 Mode: · Cinema: This mode is optimum for playing movies. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6. 1-channel sources. This mode is effective for playing sources recorded in conventional surround formats as well, because the in-phase component is assigned mainly to the center channel (C) and the reversed phase component to the surround (SL, SR and SB channels). · Music: This mode is suited mainly for playing music. The front channel (FL and FR) signals bypass the decoder and are played directly so there is no loss of sound quality, and the effect of the surround signals output from the center (C) and surround (SL, SR and SB) channels add a natural sense of expansion to the sound field. CENTER IMAGE (0. 0 to 1. 0: default 0. 3): The center image parameter for adjusting the expansion of the center channel in the DTS NEO:6 MUSIC mode has been added. 2 3 4 Press the INPUT MODE button to set the input mode to "AUTO" or "DTS". Press the STANDARD button to select the STANDARD (Dolby/DTS Surround) mode. Play a program source with the symbol. · The Dolby Digital indicator lights when playing Dolby Digital sources. · The DTS indicator lights when playing DTS sources. · D. OFF OFF LOW MID HIGH This parameter is displayed during DOLBY DIGITAL playback. or · LFE setting Lights LFE -10dB 0dB -5dB 0dB Lights · TONE DEFEAT setting Operate the SURROUND BACK button to switch Surround Back CH ON/OFF. · The SURROUND BACK indicator lights when the SURROUND BACK button is on. Lights TONE DEF. [. . . ] As with conventional DTS Surround, DTS 96/24 is compatible with a maximum of 5. 1 channels, so sources recorded using DTS 96/24 can be played in high sampling frequency, multiple channel audio with such normal media as DVD videos and CDs. Thus, with DTS 96/24, the same 96 kHz/24-bit multi-channel surround sound as with DVD-Audio can be achieved while viewing DVD-Video images on a conventional DVD-Video player ( 1). Furthermore, with DTS 96/24 compatible CDs, 88. 2 kHz/24-bit multi-channel surround can be achieved using normal CD/LD players ( 1). Even with the high quality multi-channel signals, the recording time is the same as with conventional DTS surround sources. [. . . ]