User manual DENON RC-970

[. . . ] ) • When inserting the batteries, be sure to do so in the proper direction, following the “≈” and “√” marks in the battery compartment. €¢ To prevent damage or leakage of battery fluid: • Do not use a new battery together with an old one. €¢ Do not use two different types of batteries. €¢ Do not short-circuit, disassemble, heat or dispose of batteries in flames. [. . . ] Monitor TV (TV), digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons Operating a component stored in the preset memory 1 Press the mode selector button for the component you want to operate. 1 NOTE: • For the DVD player remote control buttons, function names may differ according to manufacturer. Compare with the remote control operation of the various components. Video disc player (VDP) system buttons 2 Operate the component. • For details , refer to the component’s operating instructions. Some models cannot be operated with this remote control unit. Digital video disc player (DVD), Digital video disc recorder (DVD R) system buttons SOURCE ON SOURCE OFF 6, 7 2 1 8, 9 3 DISC SKIP + SETUP TOP MENU MENU RETURN •, ª, 0, 1 ENTER AUDIO DISPLAY SUBTITLE ANGLE 0~9, +10 : Power on : Power off (DENON DVD only) : Manual search (forward and reverse) : Stop : Play : Auto search (to beginning of track) : Pause : Disk skip (for DVD changers only) : Setup : Top menu : Menu : Return : Cursor up, down, left and right : Enter : Switch the audio language : Display : Switch the subtitle : Switch the angle : 10 key SOURCE ON 6, 7 2 1 8, 9 3 0~9, +10 : Power on/Standby : Manual search (forward and reverse) : Stop : Play : Auto search (cue) : Pause : 10 key SOURCE ON 6, 7 2 1 3 0~9, +10 : Power on/Standby : Manual search (forward and reverse) : Stop : Play : Pause : 10 key SOURCE ON SETUP TOP MENU MENU RETURN •, ª, 0, 1 ENTER DISPLAY Channel +, – 0~9, +10 TV/VCR VOL +, – : : : : : : : : : : : : Power on/Standby Setup Top menu Menu Return Cursor up, down, left and right Enter Switch display Switch channels +, – 10 key Switch between TV and video player Volume up/down 32 ENGLISH Learning function If your AV component is not a DENON product or if it cannot be operated using the preset memory, it can be controlled with the accessorious remote control unit by storing its remote control signals in the remote control unit. For some remote control signals it is not possible to “learn” the signals or the device will not operate properly. In such cases use the remote control unit included with the device to operate it. System call The accessorious remote control unit is equipped with “system call” function allowing a series of remote control signals to be transmitted by pressing a single button. This function can be used for example to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on the source component’s power and set the source to the play mode, all at a signal button. (1) System call buttons Up to 12 signals each can be stored at the “CALL1” ~ “CALL6” buttons. The System Call function can be used in the “AMP”, “ZONE2”, and “ZONE3” modes. 1 Press the power ON button and the OFF button simultaneously. 1 , 8 1 3 , 7 3 , 5 2 Press the “2” button to select Learning setup. 2 (2) Storing system call signals 2, 6, 8 1 3 Press the Mode button for the component you want to learned, then press the ENTER button. Learning is not possible for the AMP, ZONE2, and ZONE3 modes. Press the power ON button and the OFF button at the same time. 3 CH SEL ENTER 2 Press the “3” button to select system call setting. 3 , 7 4 Buttons that allow learning will light. Press the button that you wish to be learned. The display will go off and the unit will enter the learning standby mode. [. . . ] 4 3 Press the mode button for the component you want to make the punch through setting, then press the ENTER button. Press the mode button for the component you want to punch through, then press the ENTER button. €¢ The punch through is set and the set returns to the normal operating mode. Up Down Enter CH SEL ENTER CH SEL ENTER RC-970 34 ENGLISH (2) Resetting “learned” buttons (4) Resetting the punch through setting Resetting (1) Resetting the preset memory 1 1 Press the power ON button and the OFF button at the same time. [. . . ]