User manual DENON RCDM33

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. · DECLARATION DE CONFORMITE Nous déclarons sous notre seule responsabilité que l'appareil, auquel se réfère cette déclaration, est conforme aux standards suivants: EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3. D'après les dispositions de la Directive 2006/95/EC et 2004/108/EC. · DICHIARAZIONE DI CONFORMITÀ Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme alle seguenti normative: EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3. In conformità con le condizioni delle direttive 2006/95/EC e 2004/108/EC. QUESTO PRODOTTO E' CONFORME AL D. M. [. . . ] · Be sure to connect the left and right channels properly (left with left, right with right). · Do not bundle power cords together with connection cables. Doing so can result in humming or noise. Audio cables Optical digital connections Optical cable Analog connections (stereo) (White) (Red) L R L R Nail, tack, etc. n To use standing alone Use the procedure below to assemble. Stereo pin-plug cable Speaker connections Speaker cables Assembling the AM Loop Antenna Signal direction Audio signal: Output Input 1 Bend in the direction of the arrow. 2 Insert into the hole. Input Output ENGLISH Speaker Connections Speakers Connecting the Speaker Cables Carefully check the left (L) and right (R) channels and + (red) and ­ (black) polarities on the speakers being connected to the RCDM33, and be sure to interconnect the channels and polarities correctly. Protection circuit The protection circuit will be activated in thefollowing cases: · When the speaker cable's core wires are touching the rear panel or screws or when the speaker cable's + and ­ sides are touching · When the surrounding temperature is extremely high · When the internal temperature rises due to extended use with a high output If this happens, unplug the power cord, then check the connections of the speaker cables and input cables. If the set's temperature is extremely high, wait for it to cool off and improve surrounding ventilation. After doing this, plug the power cord back in. If the protection circuit is activated though there are no problems in ventilation around the set or in connections, the set could be damaged. Turn off the power, then contact a DENON servicing and inquiry outlet. Getting Started 1 (L) (R) Peel off about 10 mm of sheathing from Connections the tip of the speaker cable, then either twist the core wire tightly or terminate it. the speaker terminal counterclockwise to loosen it. the hilt into the speaker terminal. Setup w q w q 2 3 4 Turn Playback Insert the speaker cable's core wire to Setting the Timer Turn the speaker terminal clockwise to tighten it. NOTE · Use speakers with an impedance of 4 to 16 /ohms. The protection circuit may be activated if speakers with an impedance other than specified are used. · Connect the speaker cables in such a way that they do not stick out of the speaker terminals. Turn on the power first. Setting the Timer "TIME Adj" is displayed for about 2 seconds. TIME Adj 10:00 10:00 10:15 ON/STANDBY ON/STANDBY [MENU/SET] [2/u] [5/ENTER] [8/i] Use [2/u] or [8/i] to set the "hours". Press [MENU/SET] or [5/ENTER]. The "minutes" display flashes. Other Functions Use [2/u] or [8/i] to set the "minutes". Press [MENU/SET] or [5/ENTER]. Troubleshooting The current time is set, and the normal display reappears. Specifications [TIME/DISPLAY] ENGLISH Getting Started Connections Setup Playback Setting the Timer Other Functions Troubleshooting Specifications Playback Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Preparations Turning the Power On Press ON/STANDBY. · The power turns on. Press again to set the power to standby. · When the power is turned on, the function that was being used when the power was last turned off is selected (vpage 27 "Last function memory"). GWhen the last function was CDH When no disc is loaded, "NO DISC" is displayed. Setting the layer to be played with priority · The layer that is played with priority when the disc is loaded can be set. · Upon purchase, the priority layer is set to the "SA-CD". <2/5> 1/3 SOURCE 1 [MENU/SET]. 2 Press When "NO DISC" is displayed, press and hold The current priority layer is displayed. [MENU/SET] again and select the layer to be played with priority. SA-CD CD Power indicator Standby Off Power on Red When the timer is set Orange [Selectable items] SA-CD CD : The SA-CD layer mode for Super Audio CDs. : The CD layer mode for Super Audio CDs. ON/STANDBY <PHONES> <VOLUME> NOTE · Power continues to be supplied to some of the circuitry even when the power is in the standby mode. When leaving home for long periods of time or when traveling, either press ON/STANDBY to turn off the power, or unplug the power cord from the power outlet. · Be sure to stop playback before turning the power off. ON/STANDBY [MENU/SET] [4/o] [6/p] This setting is stored in the RCDM33's memory and is not canceled even when the disc tray is opened or closed or the power is turned on or off. [. . . ] · Noise interference from a nearby electronic device equipped with a microprocessor, or the radio broadcast signal is weak. Hissing or buzzing · Noise interference from a noise is heard in nearby monitor, etc. , or there AM broadcasts. is interference in the broadcast signal. Humming noise · There is interference from current is heard in AM in power cords. [. . . ]