User manual DEWALT DWE4207K

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual DEWALT DWE4207K. We hope that this DEWALT DWE4207K user guide will be useful to you.

Lastmanuals help download the user guide DEWALT DWE4207K.


DEWALT DWE4207K : Download the complete user guide (2602 Ko)

Manual abstract: user guide DEWALT DWE4207K

Detailed instructions for use are in the User's Guide.

[. . . ] Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. [. . . ] Press the lower guard lock up release lever (b) to raise the lower blade guard (g) and remove the saw blade (h). Install the new saw blade onto the shoulder provided on the inner flange (gg) making sure that the teeth at the bottom edge of the blade are pointing towards the fence (away from the operator). Replace the outer flange (e), making sure that the location lugs (ss) are engaged correctly, one on each side of the motor shaft. Tighten the blade bolt (f) by turning anti-clockwise while holding the 6 mm Allen key (z) engaged with your other hand (fig. Place your thumb on the mitre arm (l) and squeeze the mitre latch (m) to release the rotating table/mitre arm (n). Swing the mitre arm until the latch locates it at the 0° mitre position. Pull down the head and lock it in this position using the lock down button (w). Check that the two 0° markings (ww) on the mitre scale (o) are just visible. Place a square (xx) against the left side of the fence (p) and blade (h). Loosen the screws (yy) and move the scale/mitre arm assembly left or right until the blade is at 90° to the fence as measured with the square (fig. Press the saw head to the right to ensure it is fully vertical and tighten the bevel clamp handle. Place a set square (xx) on the table and up against the blade (h) (fig. Loosen the bevel clamp handle (t) and turn the vertical position adjustment stop screw (zz) in or out until the blade is at 90° to the table as measured with the square. If the bevel pointer (a1) does not indicate zero on the bevel scale (u), loosen the screws (a2) that secure the scale and move the scale as necessary. ADJUSTMENTS WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw. 1, 2, 11, 12) The blade must run at a constant cutting depth along the full length of the table and must not touch the fixed table at the rear of the slot or at the front of the rotating arm. To achieve this, the traverse arms must be perfectly parallel to the table when the saw head is fully depressed. Press the saw head fully to the rear position and measure the height from the rotating table (n) to the bottom of the outer flange (e) (fig. Keeping the saw head fully depressed, pull the head to the end of its travel. Loosen the locknut (tt) in the bracket (uu) under the upper dust extraction nozzle (q) and adjust the screw (vv) as required, proceeding in small steps. WARNING: Always check that the blade does not touch the table at the rear of the slot or at the front of the rotating arm at 90° vertical and 45° bevel positions. [. . . ] Wear approved eye protection and approved dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. 12 ENGLI SH WARNING: To reduce the risk of injury, regularly clean the dust collection system. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DEWALT DWE4207K

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DEWALT DWE4207K will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag