User manual DEXAPLAN VT 623

[. . . ] VIDEO DOOR INTERCOM VIDEO DOOR ENTRY SYSTEM VT 623 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Pay attention when laying the cable through the wall that the cable opening [29 and 46] is aligned with the cable. When laying the cable through the wall, guide the cable through the cable opening of the corresponding wall bracket. Fix the wall bracket in place to the wall using the four mounting screws [9 and 10] and four wall plugs [8 and 11]. Outdoor station: Mounting with wall bracket and wedge shaped bracket (see Fig. E) The wedge shaped bracket changes the horizontal alignment of the outdoor station by 30°. You can mount it on the left or right side of the door by turning it upside down. Hold the wedge shaped bracket [15] at the desired mounting point and mark the four drill holes on the wall with a pencil. When laying the cable through the wall, guide the cable through the cable openings of the wall bracket and the wedge shaped bracket [29/32]. Fix the wedge shaped bracket in place to the wall using the four mounting screws [10] and wall plugs [11]. Fix the wall bracket [16] to the wedge shaped bracket using the four fixing screws [5]. Indoor station: Hanging on the wall without wall bracket The indoor station can also be hung on the keyhole slots [49]. Drill two holes at the desired mounting position (Ø 5 mm) with horizontal spacing of 4. 6 cm. Insert two wall plugs [8] in the drilled holes. Screw the two mounting screws [9] into the drilled holes so that the screw heads protrude approx. 5 mm from the holes. Checking function !Unpack the equipment and remove all plastic protective packaging. Provisionally lay the connection cable [14] from the intended installation location of the indoor station to the intended installation location of the outdoor station. Using the connection cable, connect the outdoor station [1] to the indoor station [2] according to the connection diagram (see Fig. If desired, connect an optional door opener [62] (not included in the package contents) with a two-core cable (not included) to the outdoor station according to the connection diagram (see Fig. Connect the low-voltage connector [13] to the connection [50]. Plug the mains adapter [12] into a mains power socket. Check the function (see Chapter "Operation"). [. . . ] You reach the respective next menu item by repeated pressing of the image adjustment button (the current menu item is pink) or the settings menu disappears after the last menu item. The corresponding setting value is displayed numerically and graphically as a bar. You can change the setting value of the respective menu item by + [41] and pressing the buttons [40]. BRIGHTNESS: CONTRAST: SHARPNESS: COLOUR: HUE: VIDEO: Brightness (0 to 100) Contrast (0 to 100) Sharpness (0 to 6) Colour saturation (0 to 100) Hue (0 to 100); not active for PAL setting NTSC or PAL (set to PAL) Disposal Do not simply throw away packaging material and worn-out equipment but send it for recycling. [. . . ]