User manual DIGITECH GENESIS1

[. . . ] Models and Effects Functions Amplifier . . 7 Warranty We at DigiTech are very proud of our products and back-up each one we sell with the following warranty: 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U. S. , to be free from defects in materials and workmanship under normal use and service. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. [. . . ] RIGHT OUTput - Use this jack in conjunction with the left output for stereo applications. Connect a second amplifier input, or the right input of a stereo power amp. LINE OUTPUT - (1/8" Stereo TRS) - Connect to a computer sound card input, or line level input with this jack. FOOTSWITCH Jack - Connect the FS300 footswitch to remotely control effects to this jack. POWER Jack - Connect only the Digitech PS913B power supply to this jack. Setup Connections The Genesis 1 has several different connection options. You can run mono into an amp or power amp, stereo into two amps, stereo direct into a mixing console, direct into a computer sound card, or any combination of these. Before connecting the Genesis 1 to your system, make sure the Genesis 1 is OFF and your system is ON. Powering Up 1. Turn the volume completely down on your system. Connect the Genesis 1's outputs to the inputs of your system. 3. Turn the LEVEL knob down to the minimum position on the Genesis 1. 6. While playing, slowly turn up the LEVEL knob to the desired listening level on the Genesis 1. 2 Below are some examples for connecting the Genesis 1 to different types of systems. When running stereo into 2 channels of a mixer, be sure to set the channel pans to hard left and hard right: Footswitch Operation If you have chosen to purchase the Digitech FS300 footswitch, you can remotely control the Genesis 1. Each button of the FS300 functions with the Genesis 1 as follows: Footswitch A - Bypasses modulation effects Footswitch B - Bypasses delay and reverb effects. Footswitch C - Bypasses all modeling and effects, Models and Effects Functions The Genesis 1's user interface doesn't complicate things with programming functions. Its basic approach provides individual settings that the user can change, without the complexity of programming. The following explains how each control functions: 3 Amplifier The Genesis1 has eleven amp models to select from including 2 models created using GENETXTM technology. Rotate the AMPLIFIER knob to select the amp model you want to use. Each amp model is labeled on the front panel. The Amplifier knob has a pointer that identifies the selected model. The amp models are: Black Face: `65 Fender Twin Reverb Boutique: Matchless DC30 Rectified: Mesa Dual Rectifier Brit Stack: `78 Marshall Master Volume Tweed: `57 Fender Tweed Deluxe Brit Combo:Vox AC30 Fuzz: A vintage fuzz distortion Hot Rod: Mesa Boogie Mark II C High Gain: A high gain tube amp GENETXTM Gain: Rectifier and High Gain HypermodelTM GENETXTM Crunch: Hot Rod and Brit Stack HypermodelTM Marshall® is a registered trademark of Marshall Amplification Plc. Vox® is a registered trademark of Korg UK. Fender, Matchless, and Mesa Boogie, are trademarks of their respective companies and are in no way associated with DigiTech. Cabinet The Genesis1 has ten cabinet types and one direct setting to select from. [. . . ] The delay time is set with the TAP-IT button. Press the button at the rate you want the delay to repeat. The delay has a range of 100ms ­ 2. 0 seconds. There are also 2 reverb types, Spring and Hall. The reverb type is dependent on which amp model is selected. [. . . ]