User manual DIGITECH GNX1

[. . . ] GENETXTM GUITAR PROCESSOR USER'S GUIDE Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. ) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash means that there are dangerous voltages present within the unit. The exclamation point indicates that it is necessary for the user to refer to the owners manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] Parameter 1 - The Number 2 Knob adjusts the rate (SPEED) of the modulating phase. Parameter 2 - The Number 3 Knob adjusts the intensity (DEPTH) of the modulation. Parameter 3 - The Number 4 Knob adjusts the amount of effected signal returned to the input of the Phaser (REGEN). * Parameter 4 - Selects the waveform used by the Phaser. Waveforms include Triangle, Sine, and Square. * Parameter 5 - Adjusts the left to right balance of the wet signal. Mod Mix - The Number 5 Knob controls the mix of wet and dry signal. Ranges from 0 (all dry) to 99 (all wet). Triggered Flanger (TRGFLG) A Triggered Flanger is the same sound as a regular Flanger but allows you to choose the starting point of the Flanger sweep. In a regular Flanger, the low frequency oscillator (LFO) is continually sweeping up and down. This means that when you begin to play, the flanger may be at the top, bottom, or any random point of the sweep. With a Triggered Flanger, every time the signal exceeds the Sensitivity level setting, the Flanger will begin at the point of the sweep that you designate with the value of the LFO Start Parameter. Parameter 1 - The Number 2 Knob adjusts the rate (SPEED) of the modulation. Parameter 2 - The Number 3 Knob adjusts the strength the signal must be (SENSTV) in order to trigger the Flanger. Ranges from 1 (requiring strong signals to trigger) to 99 (triggers with weak signals). Parameter 3 - The Number 4 Knob selects the Flanger sweep starting point (LFO ST). Mod Mix - The Number 5 Knob controls the mix of wet and dry signal. Ranges from 0 (all dry) to 99 (all wet). * These Parameters are only available using the GENEDITTM computer editor software. 21 SECTION THREE - EFFECTS AND PARAMETERS Triggered Phaser (TRGPHA) A Triggered Phaser is the same sound as a regular Phaser but allows you to choose the starting point of the Phaser sweep. In a regular Phaser, the low frequency oscillator (LFO) is continually changing the phase of the signal. This means that when you begin to play, the phaser may be at the any random point of the phase. With a Triggered Phaser, every time the signal exceeds the Sensitivity level setting, the Phaser will begin at the point of phasing that you designate with the value of the LFO Start Parameter. Parameter 1 - The Number 2 Knob adjusts the rate (SPEED) of the modulating phase. Parameter 2 - The Number 3 Knob adjusts the strength the signal must be (SENSTV) in order to trigger the Phaser. Ranges from 1 (requiring strong signals to trigger) to 99 (triggers with weak signals). Parameter 3 - The Number 4 Knob selects the Phaser sweep starting point (LFO ST). [. . . ] Using the FX Mode or Rhythm buttons, scroll to the left or right until the alpha-numeric Display shows MMERGE (MIDI Merge). The red numeric Display will read either On (on) or OF (off) depending upon the current status of the MIDI merge function. Press the Data Up/Down buttons to select the desired status. Press the Exit button to return to the GNX1 Presets. Factory Reset This function resets the GNX1 to its original factory settings. This procedure will erase all custom user Presets, Utility settings, and recalibrate the Expression Pedal. ATTENTION: Performing this function will erase all user-programmed data. [. . . ]