User manual DIGITECH PDS1550

[. . . ] For units equipped with externally accessible fuse receptacle: Replace fuse with same type and rating only. Electromagnetic Compatibility Operation is subject to the following conditions: ·This device may not cause harmful interference. ·This device must accept any interference received, including interference that may cause undesired operation. ·Use only shielded interconnecting cables. ·Operation of this unit within significant electromagnetic fields should be avoided. DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: declares that the product: Product Name: Product Options: conforms to the following Product Specifications: Safety: EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. [. . . ] We are proud to bring back this pedal, and we're proud that you wanted it. Although the WhammyTM has an extremely intuitive user interface, this User's Guide will help you understand the WhammyTM functions and allow you to get the most out of your purchase for years to come. Included Items The utmost care was taken while your WhammyTM was being manufactured. Everything should be included and in perfect working order. Before you get started, please make sure that the following items have been included: · · · · WhammyTM Pedal PS750 or PS0913B Power Supply User's Guide Warranty Card If anything is missing, contact the factory at once. Please take a moment to complete your warranty card. It is your safeguard should a problem arise with your WhammyTM. User's Guide Guided Tour Detailed Descriptions Page2 12 5 6 3 4 7 8 9 1. Preset Knob - This knob is used to select the WhammyTM (bend), Harmony intervals, or Detune range controlled by the treadle. Effect LED - This LED lights to indicate the effect is on. User's Guide Page3 3. Treadle - This Pedal is used to bend the input note, bend between harmony intervals, or mix detuning with your input signal. Effect Switch - This switch turns the effect on and off. Dive Bomb - Bends your input note three octaves down. Drop Tune - Bends your input note two semi-tones down with a reversed pedal action. Whammy Presets User's Guide Page6 Harmony - This group of Presets adds a harmony to your incoming signal. Both the harmony note and the input signal are mixed together as if two guitars were playing simultaneously. As you rock the pedal back and forth, the harmony note bends between two intervals specified by the selected Preset but the input signal remains unchanged. Harmony Presets include: Oct Up/Oct Dn - Bends the harmony between one octave below (toe up) and one octave above (toe down) the input note. 5th Dn/4th Dn - Bends the harmony between a fifth (toe up) and a fourth (toe down) below the input note. 4th Dn/3rd Dn - Bends the harmony between a fourth (toe up) and a minor third (toe down) below the input note. 5th Up/7th Up - Bends the harmony between a fifth (toe up) and a dom seventh (toe down) above the input note. 5th Up/6th Up - Bends the harmony between a fifth (toe up) and a sixth (toe down) above the input note. 4th Up/5th Up - Bends the harmony between a fourth (toe up) and a fifth (toe down) above the input note. 3rd Up/4th Up - Bends the harmony between a third (toe up) and a fourth (toe down) above the input note. [. . . ] A value of 0 on MIDI CC11 corresponds to a toe up position and 127 corresponds to a toe down position. MIDI CC0 is used to turn on and off the Whammy effect. Values from 0 through 64 on MIDI CC0 will turn the WhammyTM effect off, and values from 65 through 127 will turn the effect on. Calibrating the Treadle In the unlikely event that the treadle pedal does not respond properly, or that the note does not bend or return to the correct pitch, it may need to be recalibrated. [. . . ]