User manual DIGITECH RP 2000

[. . . ] AMP MODELING PICKUP MODELING ACOUSTIC MODELING MODELING GUITAR EFFECT SYSTEM CABINET MODELING EFFECTS TALKERTM RHYTHM TRAINER LEARN-A-LICKTM USER'S GUIDE DIGITAL OUTPUT Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e. g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. ) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash means that there are dangerous voltages present within the unit. The exclamation point indicates that it is necessary for the user to refer to the owners manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] This Parameter is used to select one of the two Amp Channels for editing. The Red and Green Channels are both fully programmable with Amp Type, Gain, Levels, and EQ. One Channel can be used for a clean sound and the other can be used for a distorted sound. Switching channels occurs instantly giving you more flexibility during performances. The color of the LED above the Channel footswitch and the Amp Model LED in the Matrix will change to reflect the active Channel. This Parameter selects the Amp Model, or Acoustic Model you wish to emulate. The choices include: blkfac (based on a `65 Fender Twin Reverb) BoutiQ (based on a Matchless DC30) rectif (based on a Mesa Dual Rectifier) Hotrod (based on a Mesa Boogie Mark II C) Tweed (based on a `57 Fender Tweed Deluxe) Clas A (based on a Vox AC30 top boost) brtstk (based on a Marshall JCM900) clntub crunch higain acous1 acous2 direct (a clean combo setting) (a nice crunchy combo) (a smooth singing lead tone) (a flat top acoustic guitar) (a piezo acoustic guitar) (straight guitar with no modeling) Marshall® is a registered trademark of Marshall Amplification Plc. Vox® is a registered trademark of Korg UK. Fender, Matchless, and Mesa Boogie, are trademarks of their respective companies and are in no way associated with DigiTech. RP2000 User's Guide Page 15 Section Three - Effects and Parameters Page 1 6 Section Three - Effects and Parameters The Gain adjusts the amount of drive applied by the Amp Model. Higher amounts of Gain will produce more break up or distortion. Gain is not available on the Acoustic or Direct Modeling selections. Amp Level adjusts the overall volume for the selected Amp Model. Amp Level ranges from -15dB to +15dB. Cabinet Modeling The Cabinet Modeling simulates different types of microphoned speaker cabinets. You have your choice of Cabinet Type, and Mic Placement in relationship to the speaker cabinet. The Cabinet Modeling Parameters are accessed by using the Amp Model button. The Type Parameter selects the kind of speaker cabinet that will be emulated. Your choices include: none, dark, warm, and bright. The Mic Placement Parameter simulates the placement of the microphone in relation to the speaker cabinet. Placing the mic at the center of the speaker will render a fuller sound, while placing the mic towards the edge of the speaker will sound brighter. Mic Placement ranges progressively from: micp 1 (the edge of the speaker) to micp10 (the center of the speaker). EQ Equalization is an extremely useful tool used to further shape the tonal response of your guitar signal. The EQ in the RP2000 is similar to the tone knobs on an amplifier. One advantage that the EQ in the RP2000 has over a conventional amp is that it allows you to choose the frequency of the low mid and high mid as well as the gain applied to the frequency. This gives you the freedom to select the exact tone which needs adjustment rather than using a generic frequency. This Parameter is used to turn the EQ on and off. The Bass Parameter adjust the amount of low end enhancement applied to your signal. The Bass enhancement ranges from -12dB to +12dB. The Lo-Mid Frequency Parameter lets you select the exact frequency center that will be enhanced by the Low-Mid Level. The Low-Mid Frequency ranges from 250 Hertz to 2000 Hertz. The Lo-Mid Level adjusts the amount of enhancement applied to the selected Low-Mid Frequency. The Low-Mid Level ranges from -12dB to +12dB. The Hi-Mid Frequency Parameter lets you select the exact frequency center that will be enhanced by the Hi-Mid Level. Hi-Mid Frequency ranges from 800 Hertz to 5000 Hertz. The Hi-Mid Level adjusts the amount of enhancement applied to the selected Hi-Mid Frequency. The HiMid Level ranges from -12dB to +12dB. The Presence Parameter adjusts the amount of treble enhancement applied to your signal. The Presence ranges from -12dB to +12dB. RP2000 User's Guide TalkerTM The TalkerTM is an effect designed exclusively by DigiTech, which enables your instrument to speak. The TalkerTM requires a microphone to be connected to the Mic Input on the rear panel of the RP2000. [. . . ] ATTENTION: Performing this function will erase all user-programmed data. Be sure you want to erase the memory and start fresh before continuing with this procedure. The procedure for performing a Factory Reset is as follows: 1. Press the Utility button once and scroll to the left or right until the Display shows fctrst. [. . . ]