User manual DIGITECH RP6

[. . . ] A Harman International Company S-DISCTM PROCESSING RP-6 Guitar Signal Processor/Foot Controller and Preamp Owner's Manual RP-6 Owner's Manual DECLARATION OF CONFORMITY Manufacturer's Name:Harman Music Group Incorporated Manufacturer's Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product Name: Product Options: RP-6 All (requies a Class II power adapter that conforms to the requirements of EN60065, EN60747, or equivalent). conform to the following Product Specifications: Safety: EN 60065 (1993) IEC 65 (1987) with Amendments 1, 2 & 3 EN 55013 (1990) EN 55020 (1991) EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. Harman Music Group Incorporated Vice President of Engineering 8760 S. Sandy Parkway Sandy, Utah 84070, USA Effective October 1, 1996 European Contact: Your Local DigiTech Sales and Service Office or International Sales Office 3 Overlook Drive #4 Amherst, New Hampshire 03031, USA Tel (603) 672-4244 Fax (603) 672-4246 Section 7 - Appendix RP-6 Owner's Manual Table Of Contents . [. . . ] tun will appear briefly in the display window followed by --- to indicate that you are in Tuner mode. To begin tuning play a note on your guitar (a harmonic at the 12th fret will work best). The display window will show the note being played and the horizontal Parameter Matrix LEDs just under the tuning bar will light. Once the LED directly under the IN TUNE of the tuning bar is lit, the note will be in tune. If the note is not in tune, 1 or 2 of the LEDs left or right of the IN TUNE LED will be lit. If they are to the left, the note is flat and should be tuned up. If the LEDs are to the right, the note is sharp and should tuned down. You can change your tuning preference by using the value <UP> and <DOWN> keys. The default factory setting is : A=440 Hz. The tuning reference control ranges from 427 Hz to 453 Hz, which is the equivalent of ± 50 cents (1/2 semitone) in either direction form 440 Hz. When you scroll down from 427 Hz, you will also find alternate dropped tunings. Alternate tunings are A = Ab (415), A = G (392), and A = Gb (370). The display window will briefly flash the currently selected tuning preference. Exit this mode by pressing any of the footswitches. When you exit this mode, the RP-6 will default to the last mode you used. Tuner is disabled in Edit mode. Section 2 - Basic Operations 12 On/Off RP-5 Owner's Manual SECTION 3 - EFFECTS AND PARAMETERS ABOUT THE PARAMETER MATRIX The Parameter Matrix displays all the Effects and Parameters you can find in the RP-6. The Parameters are arranged in rows and columns. Use the Parameter Select keys to navigate the matrix. The Effects and their Parameters are as follows: Compression Parameters Threshold Displayed Values OFF-ON LO-1. . . 78-HI The RP-6's Compression can be used to increase sustain and to tighten up guitars, and is particularly useful on clean sounds. Parameters of the RP-6 compressor are as follows: On / Off. . . . . . . . . . . . . . . . . . . . . . . . . . Turns the Module on or off. Amount . . . . . . . . . . . . . . . . . . . . . . . . . . Controls the amount of compression applied to the signal. Higher settings yield a tighter, more focused sound, while lower settings allow better dynamics. [. . . ] For example, if you choose to program your Level to 50, both Delays 1 & 2 will be 50. Delay Parameters are as follows: On / Off. . . . . . . . . . . . . . . . . . . . . . . . . . Turns the Effect on and off. Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Determines the type of delay. Type 1 is a mono delay, Types 2 through 4 are two tap mono delays, and Types 5 through 7 are two tap stereo delays (see chart below for further information). [. . . ]