User manual DIGITECH RPX400

[. . . ] User's Guide IMPORTANT SAFETY INFORMATION LITHIUM BATTERY WARNING CAUTION! The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrow point in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner's manual. These symbols warn that there are no user serviceable parts inside the unit. [. . . ] The Number 3 and 4 knobs have no function when the Detune effect is selected. Pitch Shift A Pitch Shifter copies the incoming signal, then shifts the pitch of the copied note to a different note. The shifted note is then mixed back with the original signal sounding as if two guitars were playing in harmony. Parameter 1 - The Number 2 Knob selects the interval of the shifted pitch. Ranges from -12 (12 semitones below) to 24 (24 semitones above). Mod Level - The Number 5 Knob controls the volume of the shifted pitch. The Number 3 and 4 knobs have no function when the Pitch Shift effect is selected. 18 Creating Presets WhammyTM WhammyTM is an effect that uses an Expression Pedal to bend the pitch of the incoming signal, or add a bendable harmony with the original signal. As the Pedal is moved, the note will bend either up or down. When WhammyTM is selected, it is automatically placed before the Amp Modeling as shown in the block diagram (at the beginning of the Effects section). The WhammyTM effect must be linked to the Expression Pedal in order to function. See page 18 for more information on linking the Expression Pedal. Parameter 1 - The Number 2 Knob selects the interval and direction of the pitch bend. Choices are as follows: Harmony Bends (Dry Signal Added) Whammy (no Dry Signal) M3>MA3 (a minor third to a Major third) 1OCTUP (1 octave above) 2NDMA3 (a second above to a Major third 2OCTUP (2 octaves above) above) 2NDDWN (a second below) 3RD4TH (a third above to a fourth above) REV2ND (a second below reversed pedal action) 4TH5TH (a fourth above to a fifth above) 5THOCT (a fifth above to an octave above) 4THDWN (a fourth below) HOCTUP (one octave above) 1OCTDN (an octave below) HOCTDN (one octave down) 2OCTDN (2 octaves below) DIVBOM (Dive Bomb) Mod Level - The Number 5 Knob adjusts the volume of the WhammyTM. The Number 3 and 4 knobs have no function when the WhammyTM is selected. Delay Delay is an effect that will record a portion of the incoming signal, and then play it back a short time later. The recording can repeat just once, several times, or infinitely (which turns off the input to the Delay and allows you to play over the top of a passage in the Delay loop). Delay On/Off - The Number 1 Knob turns the Delay on (On) and off (OF). Delay Type - The Number 2 Knob selects one of the 3 different types of Delay. Values include: DIGTAL (Digital Delay), ANALOG (Analog Delay), P PONG (Ping Pong Delay). Delay Time - The Number 3 Knob adjusts the amount of Delay time. Ranges from 10 MS through 990 MS (10 through 990 ms in 10 ms increments), and 10 SEC through 20 SEC (1 second through 2 seconds in 100 ms increments). Feedback - The Number 4 Knob adjusts the number of times the delayed signal will repeat. Ranges from 1 to 99 and rhold (infinite repeat). Delay Level - The Number 5 Knob adjusts the volume of the Delay signal. [. . . ] · Dry mic can only be recorded on a separate track, not as part of a mix. To record mic, go to the setup level of the matrix and select MICDRY in USB1-2 Source or USB3-4 Source. · Mic with reverb or effects can be recorded as a mix with guitar. The Mic setup must be set to either MICRVB or MIC FX. [. . . ]