User manual DIGITECH TSR6

[. . . ] By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. DECLARATION OF CONFORMITY Manufacturer's Name: Manufacturer's Address: declares that the product: Product name: Product option: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA TSR6 all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent. ) conforms to the following Product Specifications: Safety: EMC: IEC 60065 (7th ed. 2001) EN 55013 (2001+A1) EN 55020 (1998) The product herewith complies with the requirements of the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC. Sandy Parkway Sandy, Utah 84070, USA Date: January 02, 2009 European Contact: Your local DigiTech Sales and Service Office or Harman Music Group 8760 South Sandy Parkway Sandy, Utah 84070 USA Ph: (801) 566-8800 Fax: (801) 568-7583 Supplementary Information: Table of Contents Section One - Introduction Getting Acquainted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once you have a sound close to what you are after, begin editing the effect parameters by pressing the Edit Up/Down buttons and selecting the Effect row you want to edit. To turn on or off an Effect row, press Knob 1 and then use Knobs 2-4 to modify the effects parameter settings. Anytime a stored value within a preset is changed, the Store button LED lights up. This indicates that you need to store the changes. Changing presets, or turning the power off before storing any changes erases any edits made and the TSR6 will revert to the stored values for the preset. 17 Storing/Copying a Preset Once the preset has been modified to your liking, you may store your settings to any of the 50 User preset locations (presets 1-50). The following steps outline the procedure for storing changes to a preset or copying a preset to a different location: 1. Press the Store button once and the current Preset location will flash in the Display. This is asking you to select a new User Preset location where your new sound will reside. If desired, select a new User Preset location using the Footswitches. 3 Press the Store button again to save the changes. The procedure for copying one Preset to another Preset location is the same. Comp Model - Knob 1 selects one of two Compressor models: DC (DigiTech® Main Squeeze Compressor) or CS (Based on a Boss® CS-2 Compressor/Sustainer). Press this knob to turn the selected Compressor models on and off. Sustain - Knob 2 adjusts the amount of sustain. Tone/Attack-Knob3 adjusts the tone for the DigiTech Compressor, or attack for the Boss CS-2. Compressor Level - Knob 4 adjusts the Level from the Compressor. Attack (X-EditTM only for DigiComp) - Knob 4 adjusts the amount of time the Compressor takes to respond to a signal that exceeds the threshold. Ranges from 0 to 99. Compressor 21 Distortion The TSR6 models the tones of 10 popular distortion stompboxes, each of which can be tweaked and modified, just like the real thing. Distortion Model - Knob 1 selects one of 4 Distortion models. Press this knob to turn the selected Distortion model on and off. tS - Based on an Ibanez® TS-9 gr - DigiTech® Grunge t8 - Based on an Ibanez® TS-808 mz - Based on a Boss MT-2 Metal Zone® op - Based on a DOD® 250 Overdrive/Preamp rm - Based on a DOD Gonkulator Ring Mod rt - Based on a Pro Co RATTM ff - Based on an Arbiter® Fuzz FaceTM ds - Based on a Boss® DS-1TM Distortion bm - Based on an Electro-Harmonix® Big Muff Pi® DigiTech and DOD are trademarks of Harman International Industries, Inc. Other product names modeled in this product are trademarks of their respective companies that do not endorse and are not associated or affiliated with DigiTech or Harman International Industries, Inc. [. . . ] While pressing down the Down Footswitch, begin playing the overdub phrase to be added to the loop. When the Down Footswitch is released, the display will briefly flash PL and the looped phrase will continue with the newly added overdub phrase added. To stop the Phrase Looper, press and release the left Down Footswitch quickly. You can resume playback by pressing this footswitch again. [. . . ]