User manual DIRT DEVIL EDGE

[. . . ] • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • Do not handle system or appliance with wet hands. • Do not put any object into openings. • Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow. [. . . ] 3. Put desired attachments on wand as needed. Do not attach or remove handle or wands while cleaner is ON. This could cause sparking and damage the electrical contacts. CAUTION 5 PERFORMANCE FEATURES Edge Cleaner The Edge has built-in channels on both sides that allow dirt and debris to flow in from the edges freely. Vacuuming close to baseboards and furniture will capture dirt trapped at carpet edges. Channels Overload Protector The Edge has built-in protection against motor and belt damage should an obstruction cause the roller brush to suddenly stop. The overload protector will activate when the powerhead consumes more power than planned or an obstruction makes the brush hard to turn. If this occurs: • Turn off the vacuum and remove hose handle from the wand. • Remove the object that is preventing the brush from rotating. • 30 - 60 seconds of cool-down time may be required for the circuit breaker to automatically reset. • Reconnect the hose handle to the powerhead and proceed to clean. Suction Control The suction control allows you to easily change the vacuum suction for different fabric and carpet weights. Opening the control decreases suction for drapes and lightweight rugs, while closing the control increases suction for upholsteries and carpets. Handle Release Pedal The handle release pedal allows you to lower the wand and handle for extended and easier reach under furniture. Handle Release 6 MAINTENANCE AND CARE Always unplug electrical cord and vacuum hose before servicing and maintaining the Edge Electric Powerhead. Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting. Always follow all safety precautions specified when caring for your Edge. WARNING: Brush Cleaning Check the brush roll and brush support areas frequently in order to maintain optimum efficiency. If hair, string, thread, carpet fiber or lint becomes wound around the brush roll, remove by unwinding them by hand or carefully cutting with scissors. If buildup becomes excessive, disconnect the EDGE Powerhead from the wand assembly and follow the Brush Replacement steps on page 8. Instructions can also be found under the light cover. Belt Removal and Replacement The belt should also be checked periodically to be sure it is in good condition. It should be replaced if it is stretched, cracked or broken. If the belt needs replaced, use only Edge Belt #9204-01. To remove belt: 1. Remove cover • Depress Neck Release Pedal and remove (8) #10 Torx screws, set aside for reassembly. Note: 3 longer screws are in front of the brush roller. • Turn Edge right side up and lift cover making sure pedals stay secure in cover housing. 2. Remove secondary cover • Remove clear plastic neck release lever and return spring-set aside. • Remove 3 #10 Torx screws and set aside • Lift secondary cover and slide by wiring harness. Remove 8 Torx Screws Remove 3 Torx Screws 7 MAINTENANCE AND CARE 3. Remove Brush Roller Assembly • Lift Roller Assembly while guiding end cap past belt. [. . . ] Be certain wires do not become “pinched. ” 9 EDGE REPLACEMENT PARTS Neck - 9192 Cover - 9191 Motor Cover-9209 Wire Coupler - 9198 Noise Reducer - 9199 Circuit Protector - 9200 Height Adjustment Assembly - 9194 LED Light Bar - 9201 Brush Roll - 9193 Motor 9196 Long Screw-9211 Short Screw - 9210 Rear Wheel 9203 Rear Wheel Axle - 9202 Belt - 9204-01 Front Wheels w/ Stirrup - 9197 10 LIMITED WARRANTY H-P Products, Inc. warrants that the Edge Electric Powerhead, when used for household purposes, pursuant to Seller’s instructions, will be free from defects in materials and workmanship for a period of one (1) year from the date of the initial consumer purchase. warrants that the Edge Electric Powerhead, when used in a commercial application, pursuant to Seller’s instructions will be free from defects in materials and workmanship for a period of ninety (90) days from the date of initial sale by H-P Products, Inc. This warranty does not cover consumable parts such as light bulbs and replacement belts. [. . . ]