User manual DIRT DEVIL ELECTROGLIDE REV 03-00

[. . . ] · Do not handle system or appliance with wet hands. · Do not put any object into openings. · Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow. · Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. [. . . ] The headlight will operate when the Electroglide is turned on. The powerhead has a height adjustment pedal for various carpet heights. Use the low setting for short napped carpets, and the high setting for plush carpets. Pile Height Indicator Handle Release Pedal Pile Height Pedal ELECTROGLIDE ATTACHMENTS Hose Handle Attachments If the Electroglide is attached, turn cleaner OFF before removing hose handle from wands. Press lock button, then pull to remove handle from wand. Slide attachments firmly on handle as needed. Wand Assembly Attachments To remove wands from the Electroglide Powerhead, lock wands in straight up position. Press easy release pedal with foot and pull the wands straight up out of the Electroglide Powerhead. The Electroglide plug and cord do not have to be removed to use attachments on the wands. Put attachments on wands as needed. Wand Easy Release Pedal Caution: Do not attach or remove handle or wands while cleaner is ON. This could cause sparking and damage the electrical contacts. ELECTROGLIDE 7 PERFORMANCE FEATURES Edge Cleaner Active brush edge cleaners are on both sides of the Electroglide. Therefore, guide either side of the Electroglide along baseboards or next to furniture to help remove dirt trapped at carpet edges. Overload Protector The Electroglide has built-in protection against motor and belt damage should the brush jam. If the brush slows down or stops, the overload protector button pops up and shuts off the Electroglide automatically, while the power unit motor continues to run. To reset the system, just push in the overload protector button. Suction Control The suction control allows you to easily change the vacuum suction for different fabric and carpet weights. Opening the control decreases suction for drapes and lightweight rugs, while closing the control increases suction for upholsteries and carpets. Decrease Suction Increase Suction Handle Release Pedal The handle release pedal allows you to lower the wand and handle for extended and easier reach under furniture. Handle Release Pedal 8 ELECTROGLIDE MAINTENANCE AND CARE WARNING Always unplug electrical cord and vacuum hose before servicing and maintaining the Electroglide Electric Powerhead. Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting. Always follow all safety precautions specified when caring for your Electroglide. Light Bulb Replacemnent 1. Disconnect cleaner from electrical outlet. Remove light cover by pressing in and lifting both sides of cover as shown. Push In And Turn 3. Push in and turn bulb counter clockwise to remove. Replacement bulb must not be higher than 15 watts (Part #7967). Close light cover until it snaps in place. Brush Cleaning Check the brush roll and brush support areas frequently in order to maintain optimum efficiency. If hair, string, thread, carpet fiber or lint becomes wound around the brush roll, remove by unwinding them by hand or carefully cutting with scissors. If buildup becomes excessive, disconnect the Electroglide Powerhead from the wand assembly and follow the Brush Replacement steps on Page 11. [. . . ] No. 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No. Part Description Illus. No. 27 28 29 30 31 32 33 34 35 36 37 40 41 42 43 44 45 46 51 53 55 Part No. Part Description 20 21 22 23 24 25 26 7922 Wand (Upper) 7923 Wand (Lower) 7972 Cover, Power Head 7925 Screw 8-18 x 1-7/8 (2) 7926 Nozzle Housing 7927 Bumper 7967 Bulb, Light (15 Watt) 7965 Socket, Bulb 7929 Swivel 7930 Swivel Seal (2) 7931 Pad, Foot Pedal 7932 Indicator Lever 7933 Indicator Cam 7934 Indicator Block 7935 Spring Assist 7936 Brush Assembly 7937 Washer, Metal (12 x 1/2) (2) 7938 Bearing & Housing Assembly (2) (includes Illus. 18) 7939 Lifter 7940 Handle Release 7941 Overload Protector 7942 Wire Connector 7943 Roller, Rear (2) 7944 Rear Axel (2) 7945 Base 7946 Front Axel Assembly 7947 Swivel Cap 7948 Washer Thrust 7949 Washer 7950 Catch Indexing 7951 Ratchet Catch 7952 Screw Type 25 #6 Pan (2) 7953 End Brush Tufted 7954 Brush Sprocket 7955 Brush Sprocket Flange 7928 Easy Release Pedal 7958 Screw 8-18 x 5/8 (2) 7959 Motor Bridge 7960 Belt, Cogged 7961 Motor 7962 Motor Adjustment Spring 7963 Lens, Height Adjustment 7964 Button, Extention 7973 Seal, Overload 7969 Cover, Plug 7968 Lens, Light 14 ELECTROGLIDE LIMITED WARRANTY H-P PRODUCTS, INC. warrants that the Electroglide Electric Powerhead, when used for household purposes, pursuant to Seller's instructions, will be free from defects in materials and workmanship for a period of one year from the date of the initial consumer purchase. [. . . ]