User manual DIVCO FUSION HDTV FUSIONHDTV5 USB NANO HARDWARE MANUAL

[. . . ] FusionHDTV 1 Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1 1. 2 1. 3 FusionHDTV Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FusionHDTV System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. 1 2. 2 2. 3 Installing FusionHDTV Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please remove the power cord from the PC. Warning: All specifications and information are subject to changes without further notices 20 3. 3 Connecting Power UP cable We have 2 Power Up functions - the PME and power switch cable. If your mainboard supports the PME (Power Management Event) option, you can skip the `Connecting Power UP cable' steps. We recommend that you enable Wakeup by PME# of PCI in bios-Power Management Setup. This option is different according to the bios manufacturer of the mainboard, so it is important to refer to the manual of the mainboard for the PME option. Please check if PME jumper has been done to PME side properly. If you want to change the bios setting, please press the DELETE key (AwardBios) as soon as you boot. (AMI Bios : F2 key) 1) Shut down your computer and unplug main power cord. 3) Locate the ATX power switch pins on your computer case and trace the wires to the power switch connector on your mainboard. The ATX power switch cable is normally a twisted pair of cables with a two-pin connector as shown in the picture below. < Note > On the mainboard, the ATX power switch pins are usually labeled "POWER SW" or something similar. It is vital to remember the position of these pins for a later step in the installation process. 4) Unplug the ATX power switch cable from the mainboard and connect it to the connector named "Case Power Pin" on the FusionHDTV TV PCI Tuner Card, as shown in the picture below. And you need to change the PME jumper to SW The ATX power switch cable is not polarized. 5) Connect the black socket of the Power Up power patch cable to the power switch connector on the mainboard. 6) Connect the white socket of the Power Up cable to the connector named "M/B Power Pin" on the FusionHDTV PCI Tuner card. All specifications and information are subject to changes without further notices 21 < Note > Please double check if everything has been done properly. If you plug the cables into an incorrect pin, your PC may not start or may function improperly. The location of PME jumper is different according to TV card model. [ DVB-T Pro ] M/B Power Pin Case Power Pin PME/SW Selector [ DVB-T DUAL Digital 4 ] M/B Power Pin Case Power Pin PME/SW Selector PME/SW Selector M/B Power Pin Case Power Pin [ 5 RT GOLD, 5 Express] M/B Power Pin Case Power Pin PME/SW Selector [ 5 RT Lite ] - PME jumper used to PME# option in Bios. - S W jumper used to connecting the Power pin. -----------------------------------------------------------------------------------------------------------------------------------------All specifications and information are subject to changes without further notices 22 << Note >> Connect the white end of the Power Up cable to the TV tuner card and the black end to the mainboard. If you plug the cables into the incorrect pins, your PC may not start or otherwise function improperly. If you don't want to use Power Up Scheduling from the Windows Shutdown state, you can skip the power switch circuit connections. In other words, you can skip Power Up Connecting. You can still use scheduled recording from Standby mode or powered on state. Power Up will start your computer in advance of 5 minutes before the schedule time. [. . . ] With multifunctional remote control you will be able to boot your PC from a distance. Not only does it provide perfect control of all HDTV functions you will also be able to control Windows MCE 2005 and many other application programs with this multifunctional remote control. All specifications and information are subject to changes without further notices 29 [ Fusion USB Remote ] 1 2 5 8 3 6 9 15 4 7 10 13 12 1) HDTV button: Start or Exit FusionHDTV program. 2) ~ 11) numberic button 12) Back Channel button. 13) Mute button 11 14) Snapshot button: is used for still image capture. [. . . ]