User manual DLS NORDICA 10

[. . . ] Larger enclosures must have bracing inside to avoid vibrations. The enclosure must be completely airtight. Use sealing compound in all joints, also around the cable terminals. [. . . ] Make sure to connect in ways that don't ruin the amplifier. If you have a DLS Ultimate amplifier it's possible to connect two subwoofers in parallel, these amplifiers are 1 ohm stable. We also recommend the use of a subsonic high pass filter. This gives a better bass reproduction with less "rumble". In most DLS amplifiers this feature is already built-in. For wiring use high class speaker wires, min AWG11 (4 mm2). For example DLS SC 2x4. Important Think of the speaker weight when you do your install. Use heavy bolts when fastening the sub to the enclosure baffle. Break-in period Allow the speaker to play for at least 15-20 hours. After this time the performance is correct. Enclosure damping Most enclosures should be damped inside with synthetic (acoustic) wool or damping mat (line). Attach the damping material on the wall opposite from the speaker and port. In a sealed box we recommend the use of damping wool. Warranty service This speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product. Technical Assistance For technical assistance ask the shop where the product was sold or the distributor in your very country. You can always contact the DLS Helpdesk in Sweden on e-mail : info@dls. se Information can also be found on our WEB-site www. dls. se We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. DLS Svenska AB P. O. Box 13029 SE-40251 Göteborg, Sweden Tel: +46 31 840060 Fax: +46 31 844021 E-mail: info@dls. se www. dls. se Technical specifications for DLS Ultimate Nordica 10 Nordica 10 Art. no Size Impedance Rec. range Voice coil, diameter Voice coil length X-max Cms SD Cone material Magnet, diameter Installation depth Mounting hole Outer diameter Weigth 10-25910 25 cm (10") 4 ohm 200 W min, 500 W max 25 Hz - 2 kHz 50 mm (2") 31 mm (1, 22") +-11, 5 mm (0, 45") 0, 16 mm /N 314 cm2 Aluminium 144 mm (5, 67") 140 mm (5, 51") 236 mm (9, 29") 265 mm ( 10, 43") 6, 7 kg (14, 77 lbs) Re, DC-resistance BL product Sensitivity (SPL 1W/1m) Resonant freq. (Fs) Vas (litre) Vas (ft3) Qms Qes Qts 3, 2 ohm 12 87, 0 dB 33, 7 Hz 22, 4 0, 79 9, 2 0, 65 0, 61 Technical specifications for DLS Ultimate Nordica 12 Nordica 12 Art. no Size Impedance Rec. range Voice coil, diameter Voice coil length X-max Cms SD Cone material Magnet, diameter Installation depth Mounting hole Outer diameter Weigth 10-25912 30 cm (12") 4 ohm 200 W min, 500 W max 20 Hz - 2 kHz 50 mm (2") 31 mm (1, 22") +-11, 5 mm (0, 45") 0, 203 mm/N 513 cm2 Aluminium 144mm (5, 67") 148 mm (5, 82") 282 mm (11, 1") 315 mm ( 12, 4") 7, 2 kg (15, 87 lbs) Re, DC-resistance BL product Sensitivity (SPL 1W/1m) Resonant freq. [. . . ] Alternatively you can install the enclosure on one side of the luggage compartment. Important notice! Nordica 10 & Nordica 12 have a design with "open voice coil" for improved cooling of the voice coil. This construction also give the best sound performance. To prevent dirt from entering the voice coil gap, follow these instructions: - Keep the speaker in the plastic bag until it is time for installing the speaker in the box. [. . . ]