User manual DLS RMW12

[. . . ] Larger enclosures must have bracing inside to avoid vibrations. The enclosure must be completely airtight. Use sealing compound in all joints, also around the cable terminals. The size of the enclosure is decided by the speaker data. Vented enclosures A speaker in a vented enclosure has a higher efficiency (+3 dB) and higher power handling capacity than in a sealed enclosure. [. . . ] For example DLS SC 2x4. Important Think of the speaker weight when you do your install. Use heavy bolts when fastening the sub to the enclosure baffle. Break-in period Allow the speaker to play for at least 15-20 hours. After this time the performance is correct. Enclosure damping Most enclosures should be damped inside with synthetic (acoustic) wool or damping mat (line). Attach the damping material on the wall opposite from the speaker and port. In a vented enclosure the speaker and port should be on the same side, otherwise a fade-out of some frequencies can occur. In most vehicles, except for SEDAN cars, the speaker and port should be directed backwards for best result. Technical Assistance For technical assistance ask the shop where the product was sold or the distributor in your very country. You can always contact the DLS Helpdesk in Sweden on e-mail : info@dls. se Information can also be found on our WEB-site www. dls. se We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. Warranty service This speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product. DLS Svenska AB P. O. Box 13029 SE-40251 Göteborg, Sweden Tel: +46 31 840060 Fax: +46 31 844021 E-mail: info@dls. se www. dls. se Technical specifications for DLS Reference RMW10 RMW10 Art. no Size Impedance Nom. range Voice coil, diameter Voice coil, length X-max Cms SD Cone material Magnet weight Magnet, diameter Installation depth Mounting hole Outer diameter Weigth 10-21410 25 cm (10") 4 ohm 400 W (max 600) 25 Hz - 2 kHz 75 mm (3") 20 mm (0, 79") +-9 mm (0, 35") 205 366 cm2 Aluminium one cone body 50 oz (1, 42 kg) 156 mm (6, 14") 125 mm (4, 92") 236 mm (9, 29") 266 mm ( 10, 47") 5, 3 kg (11, 68 lbs) Re, DC-resistance BL product Sensitivity (SPL 1W/1m) Resonant freq. (Fs) Vas (litre) Vas (ft3) Qms Qes Qts Single voice coil 3, 3 ohm 11, 5 87, 2 dB 35, 8 Hz 38, 5 1, 36 3, 07 0, 53 0, 45 Technical specifications for DLS Reference RMW12 RMW12 Art. no Size Impedance Nom. range Voice coil, diameter Voice coil, length X-max Cms SD Cone material Magnet weight Magnet, diameter Installation depth Mounting hole Outer diameter Weigth 10-21412 30 cm (12") 4 ohm 400 W (max 600) 20 Hz - 2 kHz 75 mm (3") 20 mm (0, 79") +-9 mm (0, 35") 162 531 cm2 Aluminium one cone body 140 oz (3, 97 kg) 180mm (7, 09") 153 mm (6") 282 mm (11, 1") 313 mm ( 12, 32") 9, 7 kg (21, 3 lbs) Re, DC-resistance BL product Sensitivity (SPL 1W/1m) Resonant freq. (Fs) Vas (litre) Vas (ft3) Qms Qes Qts Single voice coil 3, 5 ohm 17, 5 93, 5 dB 39, 8 Hz 64, 9 2, 29 3, 16 0, 28 0, 26 About the recommended enclosures The performance of these recommended enclosures will vary from vehicle to vehicle. It is more difficult to get a tight and well defined bass in a SEDAN vehicle because of the tightness between trunk and interior. In most cases the recommended enclusures on next page is the best choice. - The given enclosure volume is the inner volume. - Volumes occupied by speaker and ports have already been added to the given enclosure volumes so don't add any more volume. - Use DLS bass port kits for best result. There are two flanges coming with this kit. The larger one is for the outside, and the smaller one should be attached to the tube inside the enclosure. Make a round hole in the box where you want to mount the bass port. [. . . ] Outside box dimensions: Width : 500 mm (19, 69") Height : 320 mm (12, 60") Lower depth : 288 mm (11, 33") Upper depth : 188 mm (7, 4") Material : MDF 19 mm (3/4") Height Width Upper depth VENTED er wh Lo ept d For best result, use the recommended enclosure. If you want to modify the dimensions, use the calculation methods described on previous page. As an alternative the port can also be mounted on the side of the enclosure. 155 Technical drawing for a 26 litre enclosure. The RMW10 works well in a 26 litre vented enclosure. Here is the drawing for the box and the separate boards needed to build a suitable enclosure. 243 155 288 249 Recommended enclosure RMW12 Vented enclosure: Wiring : Single voice coil Volume : 35 / 1, 24 (liter / ft3) Port* : 4"(10, 2 cm) x 20 cm / 7, 87" Damping : Line inside F3 : 54 Hz * Use the BP 110 port kit coming with the subwoofer. [. . . ]