User manual DOLMAR BC-330 PARTS LIST

[. . . ] USE OF ALTERNATIVE FUELS CAN CAUSE THE FOLLOWING PROBLEMS: Poor engine performance, loss of power, overheating, fuel vapor lock, improper clutch engagement, premature deterioration of fuel lines, premature deterioration of gaskets, premature deterioration of carburetors. USING ALTERNATIVE FUELS AND/OR 2-STROKE OILS NOT ACCORDING TO JASO FC OR ISO-L-EGD IN DOLMAR 2-STROKE ENGINES WILL VOID YOUR ENGINE WARRANTY! WARNING! WARNING! PS-351 BC-330 EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE DOLMAR warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U. S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period. For the components listed under PARTS COVERED, the service dealer authorized by DOLMAR will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U. S. [. . . ] If the saw begins to pinch, insert a wedge to open the cut. On the last cut, do not cut the hinge. 4 28 3 2 Bucking Bucking is cutting a log into sections. 1 29 WARNING!Make sure the log will not roll down-hill. If on a slope, stand on the up-hill side of the log (see fig. Shattered wood should be cut very carefully. Sharp slivers of wood may be caught and flung in the direction of the operator of the saw. WARNING!There is an extreme danger of kickback at this point. Extra caution must be taken to maintain control of the saw. To make the felling cut, follow the sectioning method described previously (fig. If you are inexperienced with a chain saw plunge-cutting should not be attempted. Seek the help of a professional. Limbing Limbing is removing the branches from a fallen tree. Keep spark plug and wire connection tight and clean. Store saws in a high or locked place, away from children. 5 WARNING!Only properly trained professionals should work in an area where the logs, limbs and roots are tangled (i. Working in blowdown areas is extremely hazardous. Drag the logs into a clear area before cutting. Pull out exposed and cleared logs first. 6 Denomination of components 4 1 2 3 5 6 7 8 9 14 13 12 26 11 25 10 27 15 16 17 Identification plate 6" (400mm) 0 2456 528. 092. 056 42. 040. 66 Serial no. Year of manufacture 18 19 DOLMAR GmbH, 22045 Hamburg, Germany XXX. XXX. XXX Typ 94 Indicate when ordering spare parts! 24 23 22 21 20 1 Handle 2 Cover 3 Hood lock 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muffler 7 Spike bar 8 Chain tensioning screw 9 Retaining nuts 10 Chain catch 11 Sprocket guard 12 Adjusting screw for oil pump (bottom side) 13 Fuel pump (Primer) 14 Identification plate 15 Starter grip 16 Combination switch (Choke / Start / Stop) 17 Fuel pump (Primer) 18 Throttle lever 19 Safety locking button 20 Rear hand guard 21 Fuel tank cap 22 Adjusting screws for carburetor 23 Fan housing with starting assembly 24 Oil tank cap 25 Chain (Blade) 26 Guide bar 27 Sprocket guard quick tensioner 17 Technical data Stroke volume Bore Stroke Max. engine speed with bar and chain Coupling speed Sound pressure level at the operator´s ear at full load according to ANSI B 175. 1 Sound pressure level at the bystanders position (50 ft/15 m distance) according to ANSI B 175. 1 Carburetor Ignition system Spark plug or spark plug Electrode gap Fuel consumption at max. load per ISO 7293 Specific consumption at max. load per ISO 7293 Fuel tank capacity Chain oil tank capacity Mixture ratio (fuel/two-stroke oil) - when using DOLMAR High Performance oil - when using other synthetic oils (oil quality must be JASO FC or ISO-L-EGD) Chain brake Sprocket pitch Number of teeth Chain type Pitch / gauge Guide bar, length of a cut Guide-bar type Weight (fuel tank empty, without chain, guide bar and accessories) lbs ) PS-351 cu. [. . . ] Please contact your nearest service center. Spare parts Reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used. Use only original DOLMAR parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, function and safety. Original spare parts and accessories can be obtained from your local dealer. He will also have the spare part lists to determine the required spare part numbers, and will be constantly informed about the latest improvements and spare part innovations. Please bear in mind that if parts other than original DOLMAR spare parts are used, this will automatically invalidate the DOLMAR product guarantee. DOLMAR guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. [. . . ]