User manual DOLMAR ES-6 A PARTS LIST 2003-11

[. . . ] This will assist you to obtain the best possible result from your DOLMAR String Trimmer. You will note the following symbols when reading the instruction manual. Keep the area of operation clear of other persons and pets Wear eye and ear protection ­ To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the string trimmer. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. [. . . ] When asking for help, please give the following information: ­ Place of accident ­ What happened ­ Number of injured persons ­ Kind of injuries ­ Your name Dimensions : length x width x height (without nylon cutting head) Mass (without plastic guard and nylon cutting head) Volume (fuel tank) Engine displacement Maximum engine performance Engine speed at recommended max, spindle speed Maximum spindle speed (corresponding) Idling speed Clutch engagement speed Carburetor (Diaphragm - carburetor) Ignition system Spark plug Electrode gap Fuel Gear ratio mm kg L cc HP /min /min /min /min type type type mm 028") Mixed gas (gasoline : two stroke oil = 50 : 1) 14/19 1) The data is prepared taking equally into account the idling and recing or wide open throttle speed operating modes. * WARNING: MODEL MS-22C must not be used with a metal blade. CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. CAUTION: Start the string trimmer only after having assembled it completely. If the inner shaft resists full insertion of the drive shaft, try to insert it again after slightly rotating the drive shaft or the support washer on the gear case to match the inner shaft to the hole inside the holder case. ­ After making sure that the drive shaft is installed fully and properly, tighten the socket head bolt (M5 x 14) and socket head bolt (M5 x 25) to secure the drive shaft. ­Inset control cable (1) through adjusting cable (2) and fit nipple of control cable into swivel (3) of carburetor. Connect the switch cords to the two cords from the engine by inserting one into the other. CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. CAUTION: Start the string trimmer only after having assembled it completely. ­ Do not adjust position of the loop handle too close to the control grip ­The standard position of the handle is 200mm to 250mm from the hanger. Use only unleaded gasoline which contains no ethanol, or methanol (type of alcohol). This will help to avoid possible damage to engine fuel lines and other engine parts. Do not mix gasoline and oil directly in the fuel tank. IMPORTANT: Failure to follow proper fuel mix instructions may cause damage to the engine. When preparing fuel mixture, mix only the amount needed for the job you aref to do. Do not use fuel mixture that has been stored longer than two months. Fuel mixture stored longer than two months will cause hard starting and poor performance. If fuel mixture has been stored longer than this time, if should be removed and filled with a fresh mixture. Never fill the fuel tank to the very top. Never add the fuel to the tank in a closed unventilatede area. Do not add fuel to this unit close to an open fire or sparks. [. . . ] , La Mirada, California, (herein "MAKITA") warrant to the initial retail purchaser and each subsequent owner, that this utility equipment engine (herein "engine" ) was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period. For the components listed under PARTS COVERED, Makita Factory Service Center or service center authorized by MAKITA will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U. EMISSION COMPONENT DEFECT WARRANTY PERIOD The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years. [. . . ]