User manual DRAPER 73271

[. . . ] Through the radio signals, La Crosse Technology® atomic clocks always keep precise time. The changeover from standard time to daylight saving time, and vice versa, takes place automatically with the same precision. Radio Controlled Analog Clock Quick Setup Instructions Welcome to the world of atomic timekeeping technology. We hope you will enjoy the convenience of never having to set your clock again and the confidence of knowing exactly what time it is. TO SET THE TIME USING THE MANUAL TIME SET BUTTON In some cases, the La Crosse Technology® atomic clock may not receive the WWVB signal due to atmospheric disturbances or hard to reach locations such as inside shopping malls. In this case, please use the Manual Time Set button, located at the back of the clock to manually set the time. [. . . ] The minute and hour hands will fast-forward while the button is held. Keep holding the Manual Set button until the time is set as required. About 3 seconds later, the second hands will start to move and the clock is now running with manual time. Note: When the clock displays manual time, it will continue to try to receive the WWVB signal at each of the even numbered hours: 0:00, 2:00, 4:00, 6:00 . . . Remove the battery cover at the back of the clock and insert 1 AA Alkaline battery in the battery compartment. All segments of the LCD will light up briefly, then the display "-:--" and the current indoor temperature will be displayed Note: If the Display time is pressed while the analog clock is still searching for the WWVB signal, the digital clock will display "--/--" for the date and "-:--" for the world time. Wait for the digital clock to receive the WWVB time and date from the analog clock. Then the digital clock will start normal runs. BATTERY COMPARTMENT COVER DISPLAY KEY TIME SET KEY (FOR WORLD TIME) BATTERY COMPARTMENT Once the battery is installed, the clock will begin searching for a signal. For the initial setting, it is recommended to stand the clock in an upright position near a window. Within five minutes the clock will either receive the WWVB signal and set itself to the exact time (for the default Pacific Time Zone), or it will determine that the signal is not receivable at its current location and time of day. The clock will fast-forward the hands to the 4, 8, or 12 o'clock position immediately and search for WWVB at a specific time until a signal is received. Note: If the time is manually set, the clock will continue to periodically search for a signal and automatically reset the hands when the signal is received. La Crosse Technology® atomic clocks do not receive or process radio controlled time signals from Germany's DCF 77, Japan's J Ga AS, or England's MSFs atomically regulated transmitters. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. DRAPER®, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. WORLD TIME SETTING: This feature allows you to display a 2nd time from anywhere in the world. The world time can be manually adjusted by 1 hour increments (24 hour time zone). Press the Time Set key to enter world time setting. Press the Time Set key again to set the desired world time. Each key press will increase the world time by 1 hour. Notes: Once the WWVB signal has been received by the digital clock, the manually adjusted world time will be updated. If a world time has been manually set prior to reception of the WWVB time, the time in the digital clock will change correspondingly with the analog clock. [. . . ] The display will show the world time / indoor temperature. Note: The indoor temperature can only be displayed in Fahrenheit. The temperature range is from 14. 2ºF to 103. 8ºF with 0. 2ºF resolution. The temperature is updated every 20 seconds. [. . . ]