User manual DRAPER 88069

[. . . ] 5 Data security and radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction of the hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Install the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the button when the device is powered on: RESET H Press 1 to 5 sec and release – system reboot RESET (inside the needle pin hole) Press > 5 sec and release – both HOMEPLUG & WiFi FW settings return to factory default. 8|Page 4. Install the hardware Application 1 – Link to remote DSL via Powerline Via Powerline technology, the Wi-Fi homeplug can access DSL modem at other floors for internet accesses. Note that this needs Powerline to Ethernet Bridge devices at other floors, so that connection between Wi-Fi homeplug and Powerline to Ethernet Bridge can be done through the embedded HOMEPLUG technology. 9|Page Application 2 – as wireless AP + Ethernet switch The Wi-Fi homeplug can be a central 802. 11n Access point and Ethernet switch hub to link all WLAN devices and Ethernet devices. 10 | P a g e Application 3– multiple floor home networking When WLAN signal is not good to penetrate concrete floors, use Powerline technology afforded by the Wi-Fi homeplug to extend home networking range to upper (other) floors. While on the same floors, the WLAN function can be used for network-enabled devices (such as PC, NB, smart phone) to access internet. Please see the graph’s illustration. Note that this needs Powerline to Ethernet Bridge devices for users at other floors to access network resources via the Powerline communication. 11 | P a g e Application 4–as Powerline Ethernet switch By pushing the Wireless Setting button for more than 1 sec, the WiFi function of this device can be turned ON or turned OFF. In this case, Wi-Fi homeplug acts as Powerline to multiport (3 port) Ethernet switch, which, when used together with a remote Powerline Ethernet Bridge, enables two remote Ethernet devices (ex. PC, Notebook, or VIOP) on different floors or locations at home to communicate via the embedded Powerline technology. In the same time, 3 RJ-45 ports on this product can as well provide local Ethernet switch hub function. 12 | P a g e Application 5 – Wireless AP w/ Router By pushing the WiFi Setting button > 5 sec, the Router function is enabled. When keep pushing the Button, observe the LED to be OFF and ON for 5 times then release the button after the flashing LED become steady ON, By default DHCP server is enabled in the Router mode. DHCP server can assign dynamic IP address to devices connecting the LAN port of this Router. Choosing each mode will have the respect setting pages like the figure below. Please refer to the pages in the next section for the explanation of each setting. In the final step of setting, click “Finish” button and the device will reboot to apply the settings. 19 | P a g e System settings This device supports two operation modes for the IP network. Click to select one between the following two wireless operation modes, then push the “Apply” button. Item Operation mode: Access Point Operation mode: Router Time Zone Daylight Saving Admin Username Admin Password Confirm Password Description This device acts as Wireless Access Point (AP) to provide WLAN service and bridge it to wired connection. This device acts as Wireless Access Point to provide WLAN service and router to connect LAN/WLAN to the Internet. The system time will be updated from the Internet. If password is entered in the above field, enter it again here to confirm. 20 | P a g e Lan Settings Setup the LAN settings for LAN interface. Item IP Address Subnet Mask Default Gateway DHCP Server Description Setup the IP Address for the LAN interface. Setup the subnet mask for the LAN interface. This option only appears in “Access Point” mode. Setup the default gateway for the LAN interface. The DHCP Server is only available in “Router” mode. [. . . ] If the device connects to the Internet, the time will sync with the NTP server. It shows the current firmware version of the device. It shows the operation mode of the device. System Up Time Boot Loader Version Firmware version Operation Mode 28 | P a g e WAN Settings The WAN Settings only appear in Router mode. Item Connection Type Connection Status Description It display the type of the WAN interface It shows the connection status of WAN interface. For WAN-PPPoE-Manual setting, there are two buttons “Connect” and “Disconnect” here for PPPoE connection. [. . . ]