User manual DSC PC 4020 V3.0

[. . . ] Table of Contents Introduction Section 1: General System Operation 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 1. 8 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 3. 9 4. 1 4. 2 4. 3 5. 1 5. 2 5. 3 5. 4 6. 1 6. 2 6. 3 6. 4 2 3 Getting to Know Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How to Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Alternate Arming Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For example, to program May 31, 1997 type "053197. " 6. Once the date and time have been programmed, press [#] to return the partition to its normal disarmed state. 3. 5 Activating Door Chime Keypad Command: [*][4] When the door chime feature is enabled, the keypad will emit five quick beeps when a zone is opened or closed. The keypad will only beep for zones which have the door chime zone attribute enabled. Often this feature is applied to entry doors so that you are notified when someone enters or exits the premises. To enable door chime, enter [*] [4] at any keypad. To program the chime zone attribute for a particular zone, please ask your installer. NOTE: The door chime feature will not work on bypassed zones. 3. 6 View Event Buffer Keypad Command: [Master Code][9] Each system event is stored in an event buffer which can be viewed from any keypad. To view the event buffer, perform the following: 1. Enter a System Master code and press [9]. The display will read "System Master Menu. " 2. Use the keypad arrow keys (< >) to scroll to the display "View Event Buffer. " Press [*]. The event buffer can now be viewed, starting with the most recent event. When an event is presented, the first line of the display will show the event number and the partition on which the event occurred; the second line of the display will show the date and time of the event. Press the [*] key to display a description of the event. Use the arrow keys to scroll through the list of all events in the event buffer. To stop viewing events, press [#]. 18 Section 3: System Administration 3. 7 [*][7] Command Outputs 1-8 Keypad Command: [*][7][1-8] These outputs must be programmed by your installer. Up to eight command outputs can be added to your system. These outputs will operate sets of lights, door strikes and various other items depending on what you and your installer have decided to add to your system. To activate the output, enter [*] [7] followed by the output number, from 1-8. For more information regarding the [*] [7] command outputs, please ask your installer. 3. 8 Keypad Control Keypad Command: [*][6][Master Code] The brightness of the keypad backlighting and the contrast of the keypad display can be adjusted. To alter the brightness and contrast from their default settings, perform the following: 1. Press [*] [6], then enter a valid access code which has the "System Master" or "Supervisor" option enabled. [. . . ] Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. s Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. [. . . ]