User manual DSC PC2500

[. . . ] INSTRUCTION MANUAL PC25OO Incidence of Harm Should terminal equipment or protective circuitry cause harm to the telephone network, the telephone company shall, where practicable, notify the customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone company may temporarily discontinue service if such action is deemed reasonable in the circumstances. In the case of such temporary discontinuance, the telephone company shall promptly notify the customer and will be given the opportunity to correct the situation. Additional Telephone Company Information The security control panel must be properly connected to the telephone line with a USOC RJ-31X telephone jack. The FCC prohibits customer-provided terminal equipment be connected to party lines or to be used in conjunction with coin telephone service. [. . . ] The zone lights indicate the type of trouble condition. ZONE LIGHT TROUBLE 1 . . . . . . . . . . . . . . 8 . . . . . . . . . . . . . . Defective Stand-by Battery AC Power Failure (see Note below) Foil Circuit Trouble Telephone Line Problem Unsuccessful Communication Attempt with Monitoring Station Bell Circuit Failure Smoke Detector Circuit Trouble Loss of Time on System Clock Press the [#] key to return to Ready. Note: The keypad buzzer will not sound for AC failure until there is also a low battery condition. The "Trouble" light will come ON as soon as AC fails and will remain on until AC restores. SMOKE DETECTOR AND FIRE ALARM RESET If your system is equipped with smoke detectors or other fire alarm detectors, use the following instructions for resetting an alarm. To bypass a zone, enter [ ][1][Master Code][zones to be bypassed]. Press [#] to return to "Ready". 1 2 3 4 5 6 7 8 Battery A. C. Power Day loop Telephone line Communicator Bell circuit Smoke detector circuit Clock needs resetting ZONE 1 2 3 FUNCTION Ready Armed Memory Bypass Trouble Program Fire FIRE 1 4 7 2 5 8 0 POLICE 3 6 9 # The Zone Lights are used to indicate open zones. When in the "Ready" mode, a Zone Light will come ON to indicate that a zone is open. 4 5 6 7 8 KEYPAD ZONES Fire Alarm: hold down [1]+[3] Auxiliary Alarm: hold down [4]+[6] Panic Alarm: hold down [ ]+[#] These features will not function unless programmed by your installer. Labels on the keypad will indicate if features are active. The "Program" light will FLASH when Access Codes are being programmed. To change Access Codes, enter [ ][5], [Master Code][number of code to be programmed, 2 through 8][new 4-digit code]. Press [#] to return to "Ready". IMPORTANT Test system weekly; have system trouble conditions corrected by installer. The "Fire" light will come ON when a detector on the fire loop is in alarm. Press any key within 30 seconds of the alarm to silence the alarm. Press [ ][4] to reset the smoke detectors. If a fire alarm sounds at night, evacuate the premises immediately! PROGRAMMING ADDITIONAL ACCESS CODES Up to 7 access codes in addition to the Master Code can be entered from the keypad. The "Program" light will flash and the zone lights will show which codes have already been programmed. To enter a new code or change an existing code, first press the code number (1 to 8) and then ] instead of a [4 digit] enter your [4 digit] code. Note that the [ ] and [#] keys cannot be used in a code. Pressing [#] returns you to ready mode. QUICK-ARM FEATURE When the Quick-Arm feature is enabled, the panel may be armed simply by entering [ ], [0] instead of a 4 digit code. The [ ], [0] command will not disarm the panel. Enter [ ], [6], [Master Code], [4] to turn ON and OFF the Quick-Arm feature. When the command is entered, the keypad will beep 3 times if the feature is being enabled and will sound one long beep if the feature is being disabled. Press [#] to return to Ready. DOOR CHIME FEATURE The door chime feature is used, while the panel is disarmed, to provide a tone from the keypad each time a door or window is opened or closed. The doors and windows which will provide this indication are programmed by your installer. Enter [ ], [6], [Master Code], [6] to turn the door chime feature ON and OFF. [. . . ] This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security Controls Ltd. , such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. recommends that the entire system be completely tested on a regular basis. [. . . ]