User manual DSC POWER 608 V2.3

[. . . ] ·WARNING· This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Instruction Manual Software Version 2. 3 WARNING Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. System Failures This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. [. . . ] Press both * Keys for two seconds to send an AUXILIARY transmission. Press both * Keys for two seconds to send a PANIC transmission. * IMPORTANT NOTE (All Keypads): The Fire, Auxiliary and Panic keys will NOT function unless programmed by the installer. If these keys are in service and the installer has enabled audible feedback, holding down the key for two seconds will cause the keypad sounder to beep indicating that the input has been accepted and transmission is underway. The PC5516, PC5516Z, PC5532 and PC5532Z Keypads are available for applications with more than 8 zones. The functions explained in this manual are the same for all three LED keypad types. Important Note: Test system weekly and have any system trouble conditions corrected by your alarm installer. 8 9 Programming codes from an LCD Keypad: Master Code Press the [D] key to enter the function list. Scroll (< >) to. . . Press (*) for <> Press [5] or [D]. Access Codes Enter Master Access Code Enter your current Master Code. The display will read. . . (*) to Edit <> "40P" represents the Master Code. Press the [D] key to indicate that you wish to User Code 40P program the Master Code. Enter New Code Enter the new Master Code. The Master Code must be four digits long, unless 1234 <> otherwise indicated by your installer. Once the new code is entered, the keypad will beep 3 times and the display will read. . . (*) to Edit <> Press [#] to exit the code programming function. User Code 40P Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We recommend that the factory default Master Code [1234] not be used. Additional Access Codes To erase, add or change a user code, press [D] to enter the function list. Use the arrow (< >) keys to scroll to the following message. . . Press (*) for <> Press [D]. Access Codes Enter Master Access Code Enter the Master Code. Display will read. . . [*] to Edit <> Use the scroll keys (< >) to find the access code ­ indicated by "02P" to "32P" ­ User Code 01P you wish to add, change or delete. Press the [D] key to select the code you wish to change. The display will read. . . Enter New Code To add or change a code, enter the new code. Access codes must be four digits 1234 <> unless otherwise indicated by your installer. Once the 4-digit code or [D] has been entered, the keypad sounder will beep 3 times and the display will read. . . [*] to Edit <> The "P" means the code has been programmed. [. . . ] be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser's time, the claims of third parties, including customers, and injury to property. Disclaimer of Warranties This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose) And of all other obligations or liabilities on the part of Digital Security Controls Ltd. neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada. [. . . ]