User manual DUAL XIA5600

[. . . ] Suggested locations include under a seat or in the trunk. · The amplifier can be mounted horizontal (recommended) or vertical. For optimum performance, make sure to provide at least 1" of space to around all sides. Do not mount the amplifier under carpets or where airflow is restricted. [. . . ] 3 XIA5600INSTALLATION ConnectionsandControls 1 2 3 4 5 6 7 14 13 12 11 10 9 8 1 2 3 4 5 6 7 Low Level Inputs High Level Inputs Input Level Control Crossover Frequency Crossover Mode Switch Bass Boost LED Indicator 8 9 10 11 12 13 14 Ground Connection Remote Connection +12VDC Battery Connection Main Fuses illuminite Fuse illuminite Outputs Speaker Connections 4 XIA5600INSTALLATION TypicalWireRouting MainPowerConnections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle's electrical system. FuseRating When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the amplifier. Mainfuse 30 amp ATO x 3 illuminitefuse 2 amp ATO x 1 Power/GroundWireSize For optimum performance, use only the wire size listed below or larger. Make sure to use the same size power and ground wire. Power/ground4 gauge illuminiteoutput 18 gauge 5 XIA5600INSTALLATION OutputConnections The lighting elements of DUAL illuminite speakers provide you with a unique custom touch to your vehicle. Dual's patent pending illuminite LED system and control circuitry provides an extraordinary blue-hue illumination which allows great creative opportunities for the beginner and seasoned custom installer alike. DUAL XIA-series amplifiers provide a dedicated switched 12VDC output including independent fused protection (2 amp) specifically for use with illuminite speakers. DUAL illuminite speakers have two distinct sets of input terminals. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. Do not connect the amplifier speaker outputs or any audio source to the illuminite lighting inputs. Refer to the figures below for making the connections. Make sure to observe polarity as the illuminite circuitry will not operate when connected reverse polarity. Connect either red wire from the XIA amplifier illuminite outputs to the positive (+) illuminite input terminal and connect either black wire from the XIA amplifier illuminite outputs to the negative (-) illuminite input. Additionalilluminitewiringnotes: Several illuminite speakers can be connected to the 12VDC illuminite output at one time. Refer to the table below for the individual illuminite speaker current requirements. If you are unsure, consult a qualified professional or call DUAL technical assistance at 1-866-382-5476 for further information. illuminitecurrent requirements (perspeaker) XiNC112 - 55mA XiNC110 - 55mA XiNBP210 - 180mA XiNBP212 - 180mA XOBP12D - 130mA OUTPUT CONNECTOR (Plugs into amplifier) 6 XIA5600INSTALLATION AmplifierConnections SpeakerConnections Connect speaker wires observing polarity. The minimum impedance load is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XIA5600 can be wired for stereo, bridged or stereo/bridged simultaneous operation. [. . . ] The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Before you call for service, check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls may save you a service call. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. [. . . ]