User manual E-TECH WMRT01 MANUAL ADVANCED

[. . . ] User's Manual Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a commercial environment. [. . . ] If you wish, you can make some of them accessible by enabling the Virtual Server Mapping. A virtual server is defined as a Service Port, and all requests to this port will be redirected to the computer specified by the Server IP. Virtual Server can work with Scheduling Rules, and give user more flexibility on Access control. For Detail, please refer to Scheduling Rule. For example, if you have an FTP server (port 21) at 192. 168. 123. 1, a Web server (port 80) at 192. 168. 123. 2, and a VPN server at 192. 168. 123. 6, then you need to specify the following virtual server mapping table: Service Port 21 80 1723 Server IP 192. 168. 123. 1 192. 168. 123. 2 192. 168. 123. 6 Enable V V V 33 3. 5. 2 Special AP Some applications require multiple connections, like Internet games, Video conferencing, Internet telephony, etc. Because of the firewall function, these applications cannot work with a pure NAT router. The Special Applications feature allows some of these applications to work with this product. If the mechanism of Special Applications fails to make an application work, try setting your computer as the DMZ host instead. Trigger: the outbound port number issued by the application. . Incoming Ports: when the trigger packet is detected, the inbound packets sent to the specified port numbers are allowed to pass through the firewall. This product provides some predefined settings Select your application and click Copy to to add the predefined setting to your list. Note!At any given time, only one PC can use each Special Application tunnel. 34 3. 5. 3 Miscellaneous Items IP Address of DMZ Host DMZ (DeMilitarized Zone) Host is a host without the protection of firewall. It allows a computer to be exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet telephony and other special applications. NOTE: This feature should be used only when needed. Non-standard FTP port You have to configure this item if you want to access an FTP server whose port number is not 21. This setting will be lost after rebooting. 35 3. 6 Security Settings 36 3. 6. 1 Packet Filter Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. However, Inbound filter applies on packets that destined to Virtual Servers or DMZ host only. You can select one of the two filtering policies: 1. Allow all to pass except those match the specified rules 2. Deny all to pass except those match the specified rules You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the following: Source IP address Source port address Destination IP address Destination port address Protocol: TCP or UDP or both. Use Rule# · · · · · · For source or destination IP address, you can define a single IP address (4. 3. 2. 1) or a range of 37 IP addresses (4. 3. 2. 1-4. 3. 2. 254). [. . . ] Back to Connection: Then Select "Connect to network" You will see: Method2: 1. First, patch windows XP and have to install "Service package 1" Patch: http://www. microsoft. com/downloads/details. aspx?displaylang=en&FamilyID =5039ef4a-61e0-4c44-94f0-c25c9de0ace9 2. Setting on the router and client: Router: Client: Go to "Network Connection" and select wireless adapter. 82 Choose "View available Wireless Networks" like below: Advanced choose "123kk" 83 WPA: For this function, we need the server to authenticate. This function is like 802. 1x. The above is our environment: Method 1: 1. [. . . ]