User manual EAGLE TRANSDUCERS HS WSPC INSTALLATION INSTRUCTIONS

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual EAGLE TRANSDUCERS HS WSPC. We hope that this EAGLE TRANSDUCERS HS WSPC user guide will be useful to you.

Lastmanuals help download the user guide EAGLE TRANSDUCERS HS WSPC.


Mode d'emploi EAGLE TRANSDUCERS HS WSPC
Download
Manual abstract: user guide EAGLE TRANSDUCERS HS WSPCINSTALLATION INSTRUCTIONS

Detailed instructions for use are in the User's Guide.

[. . . ] INSTALLATION INSTRUCTIONS MANUAL MODELS HS-WS, HS-WSPC, AND HS-WSBK TRANSDUCERS TOOLS YOU WILL NEED: TRANSOM MOUNT: 3/8" DRILL with a variety of small bits Two (2) #12 stainless steel screws (to attach bracket to the transom. ) Marine grade caulking compound (to seal screws) SHOOT-THRU-HULL MOUNT: 100 grit sandpaper One package of the either of the following epoxies: Power Poxy®, 1 oz package. Made by: Power Poxy® Adhesives, Inc. or True Value® brand TRUE BOND epoxy or PLASTIC WELDERTM epoxy sold by True Value® stores. or Devcon® brand PLASTIC WELDERTM epoxy. Copyright © 1995 Lowrance Electronics, Inc. [. . . ] Again, check to see if you can move the transducer so it's parallel with the ground. If it doesn't, repeat step 2, but use a different letter until you can place the transducer on the transom correctly. RATCHETS 3. Once you determine the correct position for the ratchets, assemble the transducer as shown at left. Don't tighten the lock nut at this time. NUT METAL WASHER RUBBER WASHERS BOLT METAL WASHER 3 CAUTION!CLAMP THE TRANSDUCER CABLE TO TRANSOM NEAR THE TRANSDUCER. THIS WILL HELP PREVENT THE TRANSDUCER FROM ENTERING THE BOAT IF IT IS KNOCKED OFF AT HIGH SPEED. GOOD LOCATION POOR LOCATION POOR ANGLE GOOD LOCATION 4. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The bottom of the transducer bracket should be in line with the bottom of the hull. Don't let the bracket extend below the hull!Mark the center of the slots for the mounting holes. Drill two 5/32" holes in the marked locations for the #10 screws supplied with the transducer. TRANSOM SIDE VIEW 4 5. Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown above. Slide the transducer up or down until it's aligned properly on the transom as shown above. Tighten the bracket's mounting screws. Adjust the transducer so that it's parallel to the ground and tighten the lock nut until it touches the flat washer, then add 1/4 turn. If you do, the transducer won't "kick-up" if it strikes an object in the water. Route the transducer cable to the sonar unit. Make certain to leave some slack inthe cable at the transducer as shown above. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from the engine's wiring, bilge pumps, VHF radio wires and cables, and aerators can be picked up by the sonar. Use caution when routing the transducer cable around these wires. [. . . ] Make certain the area is clean, dry, and free of oil or grease, then sand both the inside surface of the hull and the face of the transducer with 100 grit sandpaper. The surface of the hull must be flat so the entire transducer face is in contact with the hull prior to bonding. SPREAD EPOXY HERE SAND THIS SURFACE 2. Follow the instructions on the epoxy package and mix it thoroughly. Do not mix it too fast, as it will cause bubbles to form in the epoxy. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE EAGLE TRANSDUCERS HS WSPC

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual EAGLE TRANSDUCERS HS WSPC will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag