User manual EBENCH KH 2264 CD RADIO CASSETTE RECORDER

[. . . ] Trouble-shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10. Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 t CD Stereo Radiorecorder e-bench KH 2264 1. Technical data This appliance is designed for casual home-use. It is not designed for continual use or for use in a commercial or industrial context. [. . . ] For medium wave (AM) reception, the device uses the internal antenna. Turn the entire appliance until you achieve the best reception result. 4. 1 Switching the device on/off The device is equipped with a FUNCTION sliding switch for all three modes: The device is switched on and is consuming electricity when the switch is switched to . . . · "Radio" for radio mode · "CD" for CD mode. The device is switched off when the switch is switched to . . . In this position, the device consumes near to no electricity, as long as none of the tape operating keys are pressed. 5. 2 Mono/Stereo When a program is broadcast on the VHF range in stereo, ST" is displayed on the device, while MONO". Should the stereo reception crackle due to bad reception . . . press the ST/MONO button to switch between the two modes. 4. 2 Adjusting the volume Turn the volume control clockwise (louder) - or anti clockwise (quieter). 4. 3 Bass-booster function Use the BASS BOOST switch to activate or deactivate the Bass booster function. 5. 3 Storing a channel You can store a total of 15 channels. When you have found a channel you would like to store . . . The display shows the number of the first memory position, and the "MEMORY" indicator flashes. You can now browse through the memory positions by pressing the M-UP button. 5. Radio mode Select "Radio" on the FUNCTION sliding switch. 5. 1 Channel search Chose a reception bandwidth. By pressing the button BAND you can switch between . . . · "FM" for VHF reception or · "MW(AM)" for med. wave reception. 6 t When the desired memory number appears on the display . . . hold the MEMORY button depressed until the "MEMORY" indicator stops flashing. Already occupied memory positions can be renewed at will. The CD is not ready for playing as long as the word "disc" is displayed. If this continues for some time, then the CD cannot be read correctly - check that the CD has been inserted the right way round and it is in good condition. 6. 2 Play / Pause If you press PLAY / PAUSE . . . · For a short time, the CD will start. The display shows the track number and track length of the track being played. · Press again while a track is being played to pause playback immediately, press again to continue playing the track from the position was paused. 5. 4 Stored channels Call up When in the normal reception mode you can browse through the 15 stored channels by . . . The channels are activated one after the other. Note: The channels are saved for a few minutes in the event of a power cut, or when changing the batteries. [. . . ] If a CD cannot be played or sounds faulty although it is in good condition . . . · Clean the lense and mechanism with a cleaning CD from a specialist retailer never use any other sort of tool. Trouble-shooting If a thorough cleaning of the CD or tape unit does not resolve the problem, it may not be caused by dirt contamination, but could a problem with the device. · In this case, please return the device to our customer service center. [. . . ]