User manual EBENCH KH 2330 DESIGNER AUDIO UNIT WITH VERTICAL CD PLAYER

[. . . ] KH 2310 · KH 2320 · KH 2330 GB DESIGNER AUDIO UNIT WITH VERTICAL CD PLAYER Operating and safety instructions Operating instructions Page 4- 9 Kompernaß Handelsgesellschaft mbH Burgstraße 21 · D-44867 Bochum (Germany) ! E & R% W Q ^ \ @ # * _8 ) $ ( = 6 5 4321`| + YUIO ^ ( \ 8 R E W % 7 = & ) _ = 9 P Q 0 T IMPORTANT SAFETY ADVICE The following safety advice must be always followed before using electrical equipment: Please read carefully through the following information concerning safety and proper use. Before reading, fold out the page with the illustrations and make yourself familiar with all the functions of the equipment. Be careful to keep these advice notes and if necessary pass them on to a third party. Do not operate the equipment if the mains plug, cable or the equipment itself is damaged. [. . . ] CD compartment @ Display # Remote control signal sensor $ Mono/stereo button (only on FM radio) % Tone selector ^ Mute switch & CD play/ pause * Device selector ( RANDOM button ) 8 Up/Forward button (*) _ Stop button (CD) / Band selector (VHF + Protective cover | Pause button (cassette only) ` Stop/ eject button (cassette only) 1 Fast forward (cassette only) 2 Rewind (cassette only) 3 Play button (cassette only) 4 Record button (cassette only) 5 Headphones connector 6 Cassette compartment 7 SNOOZE button (remote control only) 8 7 Down/Reverse button (*) 9 Functions button Aux, CD, Tuner, Tape (remote 0 INTRO button (remote control only) - SLEEP / TIMER button = M-UP/REPEAT button (*) \ MEMORY/CLK-ADJ button (*) Q Reduce volume W Increase volume E ON / OFF (standby) switch R Display / operating indicator T Mains plug Y Loudspeaker connections U Cinch connections for external devices (AUX) I Noise reduction system (cassette only) O Aerial connector P Fastening for wall mounted option control only) / MW) The operating features marked with a (*) have several different functions depending on the device selected (e. g. The operating elements | to 4 and I are exclusively for the operation of the cassette recorder. OPERATION SWITCHING ON AND OFF [ » POWER / STAND-BY « ] · · · · If the mains plug is inserted, the equipment is in Stand-by mode. To switch back to Stand-by mode, press the ON/OFF button E again. For longer periods of absence pull out the plug from the mains socket. 5 DEVICE/ SOURCE SELECT [ » CD / TUNER / TAPE / AUX « ] · Press the appropriate button * to select a device or change the source: CD = CD player TUNER = radio TAPE = cassette recorder AUX = external device, e. g. record deck ADJUST VOLUME [ » VOLUME / MUTE « ] · · · To increase the volume use the button W. To mute (silence) the loudspeakers and headphones press the mute button ^. ADJUST TONE [ » CLASSIC / ROCK / POP « ] Use the tone selector button % to set the tone quality of a track to suit the type of music and increase listening pleasure. The current setting CLASSIC, ROCK or POP is shown in the display @ - (blank display = neutral tone). HEADPHONES [ » PHONES « ] 8-32 Ohm stereo headphones 5 can be connected to the headphones connector with a 3. 5 mm jack plug. As soon as the headphones are connected the loudspeakers are turned off. Please note that high levels of sound can lead to serious hearing damage. SETTING THE CLOCK 01) 02) 03) 04) 05) 06) 07) 08) Press the Display button R to change to the time operating indicator. Press and hold down the MEMORY/CLK-ADJ button \. The 24 hour mode indicator (24 H) flashes. Press the Up/Forward button ) or the Down/Reverse button 8 to set the clock in 24 hour or 12 hour display. Press the MEMORY/CLK-ADJ button \ again - the hours indicator flashes. Set the hours using the Up/Forward button ) or the Down/Reverse button 8. Press the MEMORY/CLK-ADJ button \ again - the minutes indicator flashes. Set the minutes using the Up/Forward button ) or Down/Reverse button 8. Press the MEMORY/CLK-ADJ button \ again - the display stops flashing. The clock is now set and starts (the colon flashes). SETTING THE SWITCH-ON TIME [ » TIMER « ] If the Switch-on time feature is enabled then your Designer Audio Unit can wake you at your chosen time. 01) Using the appropriate button * select the desired device/ source (CD, TAPE or TUNER). for TUNER (RADIO) set the desired station, for TAPE (CASSETTE RECORDER) insert the tape and wind to the correct place or insert a CD and if required program a track sequence. 03) Press and hold down the TIMER button -. NOTE: You have five seconds to complete the following steps. [. . . ] 03) Press the STOP button 7 to switch of a programmed track sequence. REPEAT FUNCTIONS [ » REPEAT « ] · · · · To repeat all the tracks on a CD, press the M-UP/REPEAT button =. To repeat a single track on a CD, press the M-UP/REPEAT button = twice when the desired track is running. To repeat a programmed track sequence on a CD, press the M-UP/REPEAT button = when the programmed track sequence is running. To switch off the repeat functions, press the M-UP/REPEAT button = repeatedly until the display @ no longer shows REPEAT. PLAY TRACKS IN RANDOM SEQUENCE [ » RANDOM « ] The RANDOM function selects a random choice of tracks from the inserted CD. [. . . ]