User manual ECLIPSE TD712ZMK2 BROCHURE

[. . . ] · When installing this product, never use the existing nuts or bolts that secure parts of the fuel tank, the steering, or braking systems. Otherwise, improper steering or braking and / or a fire may result. · To prevent a short circuit from occurring, disconnect the battery's negative terminal prior to installing this product. Otherwise, an electric shock or injury may result. [. . . ] · Bundle cables and harnesses with electrical tape or wire ties to prevent them from interfering with moving parts. If they should entangle with the steering wheel, shift lever or brake pedal, an accident may result. · Never supply power to another electrical appliance by splicing or tapping into this product's power lead (battery supply or constant power wire). Otherwise, the current capacity of the wire will be exceeded, resulting in a fire or electric shock. · Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result. · When replacing fuses, be sure to use fuses of the specified capacity (amperage). Otherwise, damage to the unit, fire, or an electric shock may result. · When installing the product into a vehicle with a passenger side air bag, never install or secure the product to the air bag's cover or in places where it may impede air bag deployment. Otherwise, proper air bag operation may not be ensured in the event of an accident, causing injury or death. · When making holes using drill or similar tool, be sure to wear protective eyewear. · Do not clean the cables or cords with volatile chemicals such as alcohol, kerosene, thinner or gasoline. Using such chemicals may cause warping, discoloration or other damage. -4- Names and functions of ter minals · Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity of the power cable is exceeded, fire and electric shocks may result. · The cables should be secured with tape or similar securing method so that they will not cause an obstruction while driving. If they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal, accidents may result. [ LEFT SIDE ] F 1 DECODER UNIT E 16P 2 INTERCONNECTING CABLE (Power and speaker connector) B C D G 5 2 1 3 4 6 [ RIGHT SIDE ] 1 DECODER UNIT 3 INTERCONNECTING CABLE (Video input connector) 12P Q M N 20P J K L O R P A H I 4 INTERCONNECTING CABLE (VTR input/output connector) Tip · Refer to page 6 for details on the wire colors and connection points for interconnecting cables 2 . · Refer to page 6 and 7 for details on connection points A through R for the main unit cables and terminals. -5- Wire colors and connection points for connection cables Never connect the power supply to the speaker leads (No. 5 and No. 6), otherwise it will cause damage to the main unit. 2 Caution 1 B+ (Yellow) Connect where the power is constantly available, regardless of the ignition key's position. 2 Ground (Black) Connect where good body grounding is available. 3 DVD MUTE wire (Pink) If not using 3 and 4 , insulate them using PVC tape or similar. If they are not insulated, incorrect operation may result. Connect to H/A MUTE or DVD MUTE on the main unit. 4 NAVI MUTE wire (Brown) Connect to NAVI MUTE on the navigation unit. 5 Front speaker output leads White/Black: Gray/Black: Left Right - Connect to the front speakers. White: Left + Gray: Right + 6 Rear speaker output leads Green/Black: Purple/Black: Left Right - Connect to the rear speakers. Green: Left + Purple: Right + Main unit connectioms A E-LAN terminal Connect to the main unit or to a CD changer (sold separately) if one is being used with the system. B C D Line-out terminal (Front Mid-Low) Line-out terminal (Front / Front Mid) Line-out terminal (Front Hi) Connect to the RCA input Connectors of an external amplifier. [. . . ] White : Red : Left signal Right signal * The speakers to connect will vary depending on whether the speaker layout is 1-way speaker or 3-way speaker. (Refer to the instruction manual for details on switching the speaker layout. ) · If the speaker layout is "1-way speaker": Use the "LINE OUT" (Front/Front/Mid) terminal C . · If the speaker layout is "3-way speaker": Connect B to the low-range speaker (woofer), connect C to the mid-range speaker (squawker), and connect D to the high-range speaker (tweeter). · · · E Line-out terminal (Rear) Connect to the RCA input Connectors of an external amplifier. White : Left signal Red : Right signal -6- F Center speaker line-out terminal If using a center speaker (sold separately ), connect it to the RCA input connector of an external amplifier. G Woofer speaker line-out terminal If using a woofer speaker (sold separately ), connect it here. H I VTR input terminals (CH1) VTR input terminals (CH2) Connect the output cable of external video equipment sach as a VTR. [. . . ]