User manual ECS GS7610 ULTRA V.1.1C

[. . . ] Motherboard User's Guide This publication, including photographs, illustrations and software, is under the protection of international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] You can run the setup utility and manually change the configuration. You might need to do this to configure some hardware installed in or connected to the motherboard, such as the CPU, system memory, disk drives, etc. Running the Setup Utility Every time you start your computer, a message appears on the screen before the operating system loading that prompts you to "Hit <DEL>if you want to run SETUP". Whenever you see this message, press the Delete key, and the Main menu page of the Setup Utility appears on your monitor. If you manually clear CMOS, you need to press the F1 key that enters the Main menu page of the Setup Utility. CMOS SETUP UTILITY ­ Copyright (C) 1985-2003, American Megatrends, Inc Standard CMOS Setup Advanced Setup Features Setup Power Management Setup PCI / Plug and Play Setup BIOS Security Features CPU PnP Setup Hardware Monitor Load Optimal Defaults Save Changes and Exit Discard Changes and Exit : Move Enter: Select F1: General Help +/-/: Value F10: Save F9: Optimized Defaults Esc: Exit CPU PnP setup for configuring CPU voltage, frequency. . . etc. V02. 54 (C) 1985-2003, American Megatrends, Inc. 19 Motherboard User's Guide You can use cursor arrow keys to highlight anyone of options on the main menu page. Press Enter to select the highlighted option. Press the Escape key to leave the setup utility. Press +/-/ to modify the selected field's values. Some options on the main menu page lead to tables of items with installed values that you can use cursor arrow keys to highlight one item, and press PgUp and PgDn keys to cycle through alternative values of that item. The other options on the main menu page lead to dialog boxes requiring your answer OK or Cancel by selecting the [OK] or [Cancel] key. If you have already changed the setup utility, press F10 to save those changes and exit the utility. Press F1 to display a screen describing all key functions. Press F9 to install the setup utility with a set of default values. Standard CMOS Setup Page This page displays a table of items defining basic information about your system. CMOS SETUP UTILITY ­ Copyright (C) 1985-2003, American Megatrends, Inc. Standard CMOS Setup System Time System Date Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave S-ATA1 S-ATA2 Floppy A Floppy B 00:01:18 Mon 10/03/2005 Hard Disk Not Detected CD/DVD ROM Not Detected Not Decteted Not Detected 1. 44 MB 3 1/2" Disabled : Move Enter: Select F1: General Help +/-/: Value F10: Save F9: Optimized Defaults Esc: Exit Help Item User [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Date & Time These items set up system date and time. Primary IDE Master/Primary IDE Slave/Secondary IDE Master/Secondary IDE Slave/SATA1/2 Use these items to configure devices connected to the Primary/Secondary IDE channels. To configure an IDE hard disk drive, choose Auto. If the Auto setting fails to find a hard disk drive, set it to User, and then fill in the hard disk characteristics (Size, Cyls, etc. ) manually. If you have a CD-ROM drive, select the setting CDROM. If you have an ATAPI device with removable media (e. g. a ZIP drive or an LS-120), select Floptical. In addition, this motherboard supports two SATA channels and each channel allows one SATA device to be installed. [. . . ] When the Discard Changes and Exit dialog box appears, select [OK] to discard changes and exit, or [Cancel] to return to the main menu. Note: If you have made settings that you do not want to save, use the "Discard Changes and Exit" item and select [OK] to discard any changes you have made. 28 Chapter 4: Software & Applications Chapter 4 Software & Applications Introduction This chapter describes the contents of the support CD-ROM that comes with the motherboard package. The support CD-ROM contains all useful software, necessary drivers and utility programs to properly run our products. More program information is available in a README file, located in the same directory as the software. To run the support CD, simply insert the CD into your CD-ROM drive. [. . . ]