User manual EINHELL BT-AC 200-24 0F

[. . . ] Anleitung BT-AC 200-24 OF_SPK1:_ 28. 04. 2008 13:22 Uhr Seite 1 Bedienungsanleitung Kompressor Operating Instructions Compressor Instructions de service Compresseur Istruzioni per luso Compressore Brugsanvisning Kompressor Használati utasítás Kompresszor B f 4 j W Naputak za uporabu Kompresor Uputstva za upotrebu kompresora Návod k pouzití Kompresor Návod na obsluhu kompresora Art. -Nr. : 40. 205. 05 I. -Nr. : 01018 BT-AC 200/24 OF Anleitung BT-AC 200-24 OF_SPK1:_ 28. 04. 2008 13:22 Uhr Seite 2 Gebrauchsanweisung beachten!Læs og følg betjeningsvejledningen!Figyelembe venni a használati utasítást!4 Uvazite uputstva za upotrebu j Dodrzovat návod k obsluze! [. . . ] Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. 12 Anleitung BT-AC 200-24 OF_SPK1:_ 28. 04. 2008 13:23 Uhr Seite 13 GB 4. Technical data Power supply: Motor rating in kW/HP: Operating mode Compressor speed in rpm: Operating pressure in bar: Pressure vessel volume in litre: Theoretical intake rate in l/min. : Sound power level LWA in dB: Sound pressure level LpA in dB: Protection type: Machine weight in kg: 230 ~ 50 Hz 1. 1/1, 5 S3 25% 10 min 17500 8 24 176 94. 5 74. 5 IP 20 20 6. 1 Fitting the wheels (3) Fit the supplied wheels as shown in Fig. 6. 2 Fitting the supporting foot (4) Fit the supplied rubber stopper as shown in Fig. 6. 3 Voltage The compressor is equipped with a mains cable with shock-proof plug. This can be connected to any 230V ~ 50Hz shock-proof socket which is protected by a 16 A fuse. Before you use the machine, make sure that the mains voltage complies with the specifications on the rating plate. Long supply cables, extensions, cable reels etc. cause a drop in voltage and can impede motor start-up. In the case of low temperatures below +5°C, motor start-up is jeopardized as a result of stiffness. 6. 4 On/Off switch (8) To switch on the equipment set the On/Off switch (8) to position 1. Move the On/Off switch (8) to position 0 to switch off the equipment. 1) You can adjust the pressure on the pressure gauge (6) using the pressure regulator (7). The set pressure can be taken from the quicklock coupling (5). 6. 6 Setting the pressure switch The pressure switch is set at the factory. Switch-on pressure 6 bar Switch-off pressure 8 bar 6. You must fully assemble the appliance before using it for the first time. Operating mode S3 - 25% - 10min: S3 = Intermittent mode without influencing the starting process. This means that during a period of 10 min the max. Points to note when setting up the compressor Examine the machine for signs of transit damage. Report any damage immediately to the company which delivered the compressor. The compressor should be set up near the working consumer. Avoid long air lines and long supply lines (extensions). [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]