User manual EINHELL BT-CS 1200

[. . . ] Anleitung_BT_CS_1200_SPK1:_ 01. 02. 2008 7:22 Uhr Seite 1 Bedienungsanleitung Handkreissäge Operating Instructions Hand-held Circular Saw Mode d'emploi Scie circulaire portable Istruzioni per l'uso Sega circolare manuale lL Betjeningsvejledning Håndrundsav A Használati utasítás Kézikörfrész Bf Upute za uporabu Rucna kruzna pila 4 j Uputstva za upotrebu Rucna kruzna testera Návod k pouzití Rucní kotoucová pila Návod na obsluhu laserovej rucnej kotúcovej píly W Art. -Nr. : 43. 309. 30 I. -Nr. : 01017 BT-CS 1200 Anleitung_BT_CS_1200_SPK1:_ 01. 02. 2008 7:23 Uhr Seite 2 1a 2 1 3 10 4 9 5 8 7 13 6 1b 11 14 15 12 21 18 17 20 19 16 2 Anleitung_BT_CS_1200_SPK1:_ 01. 02. 2008 7:23 Uhr Seite 3 2 a 3 4 6 4 5 7 9 12 6 6 14 7 11 a 11 3 Anleitung_BT_CS_1200_SPK1:_ 01. 02. 2008 7:23 Uhr Seite 4 8 6 a 9 16 16 8 10 2 11 13 18 3 a 15 17 19 12 19 15 12 4 Anleitung_BT_CS_1200_SPK1:_ 01. 02. 2008 7:23 Uhr Seite 10 GB "Caution - Read the operating instructions to reduce the risk of inquiry" Wear ear-muffs. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Wear safety goggles. [. . . ] Ensure that the dust extractor line is safely and correctly connected. The moving swing guard hood must not be fixed in the retracted guard hood when the saw is in use. Saw blades whose main body is thicker or tooth set thinner than the thickness of the splitter must not be used. Always pull out the power plug before doing any work on the circular saw!6. 2 Using the circular saw Adjust the cutting depth, cutting angle and parallel stop (see section 5. 1, 5. 2 and 5. 4) Ensure that the ON/OFF switch (2) is not depressed. Only then should you connect the mains plug to a suitable socket. Do not switch on the circular saw until you have fitted a saw blade. Place the saw foot flat on the workpiece you wish to saw. The saw blade must not be in contact with the workpiece. Hold the circular saw firmly with both hands. 10) To switch on: Press the locking button (3) and the ON/OFF switch (2) at the same time Allow the saw blade to accelerate until it reaches full speed. Then slowly move the saw blade along the cutting line. Only exert gentle pressure on the saw blade as you do so. To switch off: Release the locking button and ON/OFF switch If you release the handle the equipment will shut down automatically which means that it cannot operate accidentally. Ensure that you do not cover or block the ventilation openings whilst working with the tool. 13 Do not slow down the saw blade after you switch it off by pressing it sideways. Do not put down the machine until the saw blade has reached a complete standstill. Carry out a trial cut in a piece of waste wood 6. 4 Changing the saw blade (Fig. Always pull out the power plug before doing any work on the circular saw!Only use saw blades of the same type as the saw blade supplied with this circular saw. Push back and secure the moving swing guard hood (19) using the lever for the swing guard hood (15). Use the saw blade wrench (13) to apply counterpressure to the flange (18). [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]