User manual EINHELL BT-JS 400 E

[. . . ] Anleitung BT-JS 400 E_SPK1:_ 15. 09. 2008 13:17 Uhr Seite 1 k Bedienungsanleitung Elektronik-Stichsäge Operating Instructions Electronic Jigsaw Mode demploi de la scie à guichet électrique Istruzioni per luso per seghetto alternativo elettronico Betjeningsvejledning Elektronisk stiksav Használati utasítás Elektronika-szúrófrész Upute za uporabu Elektronicka ubodna pila Uputstva za upotrebu Elektronska ubodna testera Návod k obsluze Elektronická pímocará pila Návod na obsluhu Elektrická priamociara píla t p C l L A B f 4 j W Art. -Nr. : 43. 211. 00 I. -Nr. : 01017 BT-JS 400 E Anleitung BT-JS 400 E_SPK1:_ 15. 09. 2008 13:17 Uhr Seite 2 1 2 3 1 5 4 8 13 6 7 9 10 11 12 2 12 3 11 b 8 a 13 4 2 7 Anleitung BT-JS 400 E_SPK1:_ 15. 09. 2008 13:17 Uhr Seite 3 4 5 2. 1. 9 7 6 2 7 3 1 8 9 3 Anleitung BT-JS 400 E_SPK1:_ 15. 09. 2008 13:17 Uhr Seite 8 GB "Caution - Read the operating instructions to reduce the risk of inquiry" Wear ear-muffs. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Wear safety goggles. [. . . ] To switch off the equipment briefly hold down the ON/OFF switch (3). 6/Item 1) You can pre-select the required speed with the speed selector. Turn the speed selector in PLUS director to increase the speed and turn the speed selector in MINUS direction to reduce the speed. The suitable stroke speed is dependent on the relevant material and working conditions. General rules for cutting speeds for metal cutting work must be complied with here as well. You can generally use a higher speed with fine saw blades whilst coarser saw blades require lower speeds. low stroke speed (for steel) medium stroke speed (for steel, soft metal, plastic) high stroke speed (for softwood, hardwood, soft metal, plastic) 6. 4 Making cuts Ensure that the ON/OFF switch (3) is not depressed. Only then should you connect the mains plug to a suitable socket. Do not switch on the jigsaw until you have fitted a saw blade. Anleitung BT-JS 400 E_SPK1:_ 15. 09. 2008 13:17 Uhr Seite 11 GB Use only saw blades that are in perfect condition. Replace blunt, bent or cracked saw blades immediately. Place the saw foot flat on the workpiece you wish to saw. Allow the saw blade to accelerate until it reaches full speed. Then slowly move the saw blade along the cutting line. Only exert gentle pressure on the saw blade as you do so. When cutting metal, apply a suitable coolant along the line you wish to cut. 7-8) Drill a 10 mm hole in the section you wish to saw out. Insert the saw blade into this hole and start to saw out the required section. 6. 6 Making miter cuts Set the angle on the soleplate (see section 5. 3). Observe the instructions in section 6. 4. 8. 3 Maintenance There are no parts inside the equipment which require additional maintenance. 8. 4 Ordering replacement parts: Please quote the following data when ordering replacement parts: Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www. isc-gmbh. info 9. Disposal and recycling The unit is supplied in packaging to prevent its being damaged in transit. [. . . ] Please note the following terms under which guarantee claims can be made: 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for this guarantee. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these defects or replacement of the device. [. . . ]