User manual EINHELL SB 1020-1D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual EINHELL SB 1020-1D. We hope that this EINHELL SB 1020-1D user guide will be useful to you.

Lastmanuals help download the user guide EINHELL SB 1020-1D.


Mode d'emploi EINHELL SB 1020-1D
Download
Manual abstract: user guide EINHELL SB 1020-1D

Detailed instructions for use are in the User's Guide.

[. . . ] Machine base Pillar Fixing screw Drill table Drill table clamp shaft Machine head V-belt Motor Grip knobs Drill chuck Spindle Mounting holes Hinged chip guard Depth stop (only SB 401/1) Tightening screw Screw Clamping screw (only SB 501/1) On switch Off switch Grub screw Crank precautions to observe in order to ensure that all residual hazards are ruled out. Ensure proper voltage The voltage must comply with the specifications on the rating plate. Use a socket-outlet with earthing contact The device may only be operated from an outlet with the properly installed earthing contact. Extension cable The cord cross section of an extension cable must measure at least 1. [. . . ] B Finally, fit the complete bit head to the pillar. Align the head so that it is horizontal to the base plate and fasten it in position with the screws (35). b Screw the 3 supplied handles (9) in the handle mounts. B Before you mount the drill chuck with the MK shank, check that both parts are clean. Insert the taper mandrel in the taper of the drill chuck with a powerful jolt. Important: All bare parts are greased in order to protect them from corrosion. Before mounting the drill chuck (10) onto the spindle (11), both parts must be completely degreased using an environmentally friendly solvent. 4/5) Before you use the drill for the first time it must be permanently fixed in position. To a point where they do not distort or deform the base plate. 5 Unscrew the three recessed head screws (21). Push the transparent cover (23) into the groove of the red mounting frame (24) and fasten it again with the recessed head screws (21). The height of the cover (23) is infinitely adjustable and can be locked using the two thumb screws (22). The chip guard (13) can be flipped up to enable bits to be changed. Prior to starting Ensure that the voltage of the mains supply complies with the specifications on the rating plate. Connect the machine only to a socket with the properly installed earthing contact. The table drill is equipped with a no-volt trip that is designed to protect the operator from an undesired restart following a drop in voltage. Should this occur, the machine must be manually restarted. 1/2) Make sure that the power plug is removed from the socket-outlet before changing tools. Only cylindrical tools with the stipulated maximum shaft diameter may be clamped in the scroll chuck (10). Only use a tool that is sharp and free of defects. Do not use tools whose shaft is damaged or which are deformed or flawed in any other way. Use only accessories and attachments that are specified in the operating instructions or have been approved by the manufacturer. [. . . ] Only adjust the setting when the machine is at a standstill. -Lower the drilling spindle (11) until the tip of the drill bit touches the workpiece. -Slacken the clamping screw (17) and turn the scale ring (25) forwards until it stops. -Turn the scale ring (25) back to the desired drill depth, then lock this setting into place using the clamping screw (17). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE EINHELL SB 1020-1D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual EINHELL SB 1020-1D will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag