User manual EIZO FLEXSCAN L760T-C

[. . . ] (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 Trade name: EIZO Model: FlexScan L760T-C declare that the product is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first installing the display or whenever changing the system. Adjustment Procedure NOTE · Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. 1. Press the Auto Adjustment Button on the control panel. The message "Your setting will be lost, if you press again now. " appears and remains on the screen for 5 seconds. While the message is on the screen, press the Auto Adjustment Button again to automatically adjust the clock, phase, and screen position. If you do not wish to do adjust the screen, do not press the Auto Adjustment Button again. NOTE · The Auto Adjustment function is intended for use on AT-compatible PC running Windows. It may not work properly in either of the following cases. When running an AT-compatible PC on MS-DOS (Not windows). The background color for the "wall paper" or "desktop" pattern is set to black. If the appropriate screen can not be made by using the Auto Adjustment Button, adjust the screen through the following procedures. If the appropriate screen can be made, proceed to step 4. 20 4. ADJUSTMENT English 2. We recommend setting the desktop pattern to that as shown in the diagram below. NOTE · More precise adjustment is available for using the "Screen Adjustment program" utility software. It can be downloaded from the EIZO homepage (http://www. eizo. com/). 3. Adjust by using <Screen> menu in the ScreenManager. (1) Vertical bars appear on the screen Use the <Clock> (p. 34) adjustment. Select the <Clock> and eliminate the vertical bars by using the Right and Left of the Control Buttons. Do not continuously press the Control Buttons, as the adjustment value will change quickly and make it difficult to locate the most suitable adjustment point. If the horizontal flickering, blur or bars appear, proceed to <Phase> adjustment as follows. (2) Horizontal bars appear on the screen. Use the <Phase> (p. 34) adjustment. Select the <Phase> and eliminate the horizontal flickering, blurring or bars by using the Right and Left Buttons. NOTE · Horizontal bars may not completely disappear from the screen depending on the PC. 4. ADJUSTMENT 21 English (3) The screen position is incorrect. The correct displayed position of the monitor is decided because the number and the position of the pixels are fixed. The "Position" adjustment moves the image to the correct position. Select <Position> and adjust the position by using the Up, Down, Right and Left Buttons. If vertical bars of distortion appear after finishing the <Position> adjustment, return to <Clock> adjustment and repeat the previously explained adjustment procedure. [. . . ] Rated maximum output Separation distance according to frequency of transmitter power of transmitter m 150kHz to 80MHz 80MHz to 800MHz 800MHz to 2. 5GHz W d = 1. 2 P d = 1. 2 P d = 2. 3 P 0. 01 0. 12 0. 12 0. 23 0. 1 0. 38 0. 38 0. 73 1 1. 2 1. 2 2. 3 10 3. 8 3. 8 7. 3 100 12 12 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance "d" in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where "P" is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. [. . . ]