User manual ELECTRO-VOICE 312A DATASHEET

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE 312A. We hope that this ELECTRO-VOICE 312A user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE 312A.


ELECTRO-VOICE 312A DATASHEET: Download the complete user guide (187 Ko)

Manual abstract: user guide ELECTRO-VOICE 312ADATASHEET

Detailed instructions for use are in the User's Guide.

[. . . ] There is much less coloration of the sound from resonating sources, leaving only the intended sound to be heard by the audience. Installation Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of rigging items overhead. Electro-Voice strongly recommends that the 312A be suspended in accordance with all current national, federal, state and local regulations. It is the responsibility of the installer to ensure that the 312A is safely installed in accordance with all such regulations. [. . . ] At higher frequencies, the roll-off approximately matches the power-response of the DL10X-SH (6 dB per octave). At lower frequencies, directivity is lost when the mouth is no longer large enough to maintain directional control. These two consequences can be observed in the "humped" response in Figure 3. Equalization can be easily applied with a graphic equalizer to give a flat response. The high-frequency compression driver can be equalized with a graphic equalizer or an EQ module inserted into the Electro-Voice XEQ-2 (two-way) or XEQ-3 (two-way or three-way) active crossover/equalizer. The EQ module should be selected to suit the particular compression driver and the HP420A horn (see relevant data sheet). Because of its use in large arenas, where air loss can be significant, it is recommended that the system be equalized "on site" for optimum results. The XEQ-3 and the mid-bass EQ module from the EQMT-2 can be used to provide a good starting point for the equalization. 2 Electro-Voice strongly recommends the use of a 100-Hz high-pass filter to protect the drivers from unnecessary excursion and thermal stress. Connections The four DL10X-SH drivers in the 312A horn have a nominal impedance of 16 ohms each and can be accessed individually and driven independently. It is particularly important to bear in mind the impedance of any cabling and specifications of the amplifier before selecting a specific combination. Whatever the combination selected, the polarity of the drivers must be considered (see Figure 9 and Polarity of the DL10X-SH Drivers section). Architects' and Engineers' Specifications The horn shall be of the constant-directivity type. It shall produce a horizontal beamwidth (6-dB-down angle) of 40°, deviating no more than +20°/­5° from this angle over the range of 350 Hz to 20 kHz. It shall produce a vertical beamwidth of 20°, deviating no more than +30°/­5°over the frequency range of 350 Hz to 20 kHz. The 312A mid-bass section shall operate over the range of 100 Hz to 4, 000 Hz, with a recommended crossover frequency of 1, 600 Hz, and be driven by four 10-inch, weather-resistant drivers with high-technology cones of Kevlar® and epoxy. 1 The patented Manifold Technology® technique shall be exploited and result in a power-handling capacity of 1, 200 watts per EIA Standard RS426A. The average axial sensitivity shall be 109 dB SPL at 1 meter with 2. 83 volts applied. The frequencies above 1, 600 Hz shall be produced by the supplied Electro-Voice HP420A TransPlanarTM constant-directivity horn with user-selectable driver combinations. The horn bell manifold chamber and back covers shall be constructed of fiberglass, foam and polyester resin. Two steel mounting rails shall be provided to coaxially mount the Electro-Voice HP420A horn. The horn shall have an integral rear mounting bracket made of black powder-coated 10-gauge steel. Brackets shall be provided at the front of the horn to stabilize and aim the 312A. The horn shall be 1500 mm (59. 0 in. ) high, 991 mm (39. 0 in. ) wide, 1880 mm (80. 0 in. ) long and weigh 108 kg (237 lb). [. . . ] Electro-Voice shall not be liable for any incidental or consequential damages including, without limitation, injury to persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. Other Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Electro-Voice Speakers and Speaker Systems are guaranteed against malfunction due to defects in materials or workmanship for a period of five (5) years from the date of original purchase. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE 312A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE 312A will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag