User manual ELECTRO-VOICE A20 DATASHEET

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE A20. We hope that this ELECTRO-VOICE A20 user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE A20.


ELECTRO-VOICE A20 DATASHEET: Download the complete user guide (315 Ko)

Manual abstract: user guide ELECTRO-VOICE A20DATASHEET

Detailed instructions for use are in the User's Guide.

[. . . ] The companion Xsub subwoofer systems would either be stacked on the ground underneath the Xvls/Xvlt full-range column or would be hung in a separate column suspended next to the full-range column. Each column of loudspeakers is then suspended from a grid which is in turn secured to the building structure (usually via a motorized hoist). The external X-Line rigging hardware consists of hinge assembles at the rear and chain strap assemblies at the front. To suspend the loudspeakers overhead, three different sets of rigging are required. Pro Audio Group · Telex Communications Inc. [. . . ] · 12000 Portland Ave South · Burnsville, MN 55337 USA · Tel: 952-884-4051 · Fax: 952-887-9212 www. electrovoice. com Attaching the Top Loudspeaker to the Grid: The first set of rigging is used to secure the top enclosure of the column to the grid. There are two pieces of rear rigging hardware and two pieces of front rigging hardware required for this purpose. Two types of rigging hardware may be used at the rear - either two Xvhg flexible-chain grid hinges or two Xvhl solid-arm linking hinges. This makes attachment to the grid faster; however, the grid cannot ride on top of the loudspeakers during transportation. This makes attachment to the grid a bit slower; however, the height is less and the grid may now ride on top of the loudspeakers during transportation. The Xvhg offers a higher rigging strength when the top box is angled down more than 20 degrees, while the Xvhl offers greater rigging strength when the top box is angled down less than 20 degrees. (Note that the Xvhl linking hinge is the same hardware used to link two enclosures together. ) This hardware will work for attaching any of the loudspeaker systems to the grid. The selection of whether to use the Xvhg or Xvhl for the rear rigging hardware is left to the customer. Linking One Loudspeaker to Another: The second set of rigging is used to link two enclosures together. The Bottom Stacking Dolly will not work with the rectangular Xvls or Xsub. The Front Dolly secures to the front of a single enclosure and may be used on the Xvls, Xvlt or Xsub enclosures. One Front Dolly is required for each enclosure and the rigging hardware cannot remain attached to the enclosure when riding on the dolly. Although the Front Dolly requires more effort, it offers maximum protection for the front of the loudspeaker and allows the loudspeakers to be manually lifted and carried if necessary. Most customers will typically use the Bottom Stacking Dollies for all of their Xvls and Xsub enclosures, and the Front Dolly for the Xvlt enclosures. There is not an individual dolly for the Xfil1/Xfil2 loudspeakers at this time. Telex/EV does not manufacture or sell dollies; however, the EV/Telex engineers have worked with R&R Cases (a thirdparty company which specializes in cases and hardware for the professional loudspeaker industry) to develop dollies for the X-Line loudspeakers that R&R will sell direct to our customers. The recommended digital electronic controller for use with the X-Line loudspeakers is the KlarkTeknik DN9848, which is available through the normal KT/Telex distribution. The recommended power amplifiers are the Electro-Voice P3000, which are available through the normal EV/Telex distribution. Pro Audio Group · Telex Communications Inc. [. . . ] The recommended digital electronic controller for use with the X-Line loudspeakers is the KlarkTeknik DN9848, which is available through the normal KT/Telex distribution. The recommended power amplifiers are the Electro-Voice P3000, which are available through the normal EV/Telex distribution. Pro Audio Group · Telex Communications Inc. · 12000 Portland Ave South · Burnsville, MN 55337 USA · Tel: 952-884-4051 · Fax: 952-887-9212 www. electrovoice. com X-LineTM Loudspeaker Specifications Xvls FULL RANGE LINE ARRAY LOUDSPEAKER SYSTEM Configuration: 3-Way Active Crossover Frequencies: 220Hz & 1250 Hz Nominal Coverage Pattern: 90H x 5. 0V HF Section: Drivers - Three ND5-16 16-ohm Compression Drivers Horn - 90H x 5. 0V Long-Term Power Rating - 225 watts total (75 watts each) Nominal Impedance - One 5. 3-ohm load MB Section: Drivers - Two ND08 16-ohm Midbass Drivers Horn - 90H x 5. 0V Long-Term Power Handling - 600 watts total (300 watts each) Nominal Impedance - One 8-ohm Load LF Section: Drivers - Two EVX155Plt 8-ohm Woofers Drivers Long-Term Power Handling - 1200 watts total (600 watts each) Nominal Impedance - Two 8-ohm Loads Wiring Configuration: Two Paralleled 8-Pin Neutrik NL8 Connectors Pins 4: HF (5. 33 ohms, 225 watts) Pins 3: MB (8. 00 ohms, 600 watts) Pins 2: LF2 (8. 00 ohms, 600 watts) Pins 1: LF1 (8. 00 ohms, 600 watts) System Weight: 257 lbs Enclosure Dimensions: 49. 000 in. deep Enclosure Shape: Rectangular Rigging: Proprietary Hinge on Back, Proprietary Adjustable Chain on Front Xvlt FULL-RANGE LINE ARRAY LOUDSPEAKER SYSTEM Configuration: 3-Way Active Crossover Frequencies: 220Hz & 1250 Hz Nominal Coverage Pattern: 120H x 8. 5V HF Section: Drivers - Three ND5-16 16-ohm Compression Drivers Horn - 120H x 8. 5V Long-Term Power Rating - 225 watts total (75 watts each) Nominal Impedance - One 5. 3-ohm load MB Section: Drivers - Two ND08 16-ohm Midbass Drivers Horn - 120H x 8. 5V Long-Term Power Handling - 600 watts total (300 watts each) Nominal Impedance - One 8-ohm Load LF Section: Drivers - Two EVX155Plt 8-ohm Woofers Drivers Long-Term Power Handling - 1200 watts total (600 watts each) Nominal Impedance - Two 8-ohm Loads Wiring Configuration: Two Paralleled 8-Pin Neutrik NL8 Connectors Pins 4: HF (5. 33 ohms, 225 watts) Pins 3: MB (8. 00 ohms, 600 watts) Pins 2: LF2 (8. 00 ohms, 600 watts) Pins 1: LF1 (8. 00 ohms, 600 watts) System Weight: 253 lbs Enclosure Dimensions: 49. 000 in. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE A20

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE A20 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag