User manual ELECTRO-VOICE BB4 DATASHEET

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE BB4. We hope that this ELECTRO-VOICE BB4 user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE BB4.


ELECTRO-VOICE BB4 DATASHEET: Download the complete user guide (635 Ko)

Manual abstract: user guide ELECTRO-VOICE BB4DATASHEET

Detailed instructions for use are in the User's Guide.

[. . . ] Applications of close or normal miking of speech at podiums, lecterns or pulpits normally require a windscreen to control breath noise and P-popping or, in some cases, wind noise from circulating air. A small foam windscreen is included with the RE90P-12 and RE90P-18 mics. This windscreen is made of two stages of foam (a dense exterior surrounding a sparser core) which is easily slipped over the transducer. This twostage filtering provides greater isolation from P-pop noise in a smaller package. [. . . ] This twostage filtering provides greater isolation from P-pop noise in a smaller package. In some locations, there is a desire to permanently attach the foam windscreen to the microphone to prevent loss. Included with the microphone are two strips of doublesided tape (the second strip is a spare). To permanently attach the foam windscreen, first crack and peel off the protective back layer of one strip of tape. Apply the tape to the transducer by wrapping it around the gooseneck adapter. The eight screened ports on the transducer should be well above the tape so as to not disturb the sound reception. Now, pull the windscreen down over the tape, stopping when the end of the foam is even with the flexible gooseneck. Caution: the windscreen foam is delicate and therefore easily ripped by applying too much force. Description The RE90P-12 and RE90P-18 podium microphones are phantom-powered "backelectret" miniature condenser gooseneck microphones. The back-electret feature provides greater sensitivity, wider frequency response, and superior immunity from handling noise than a diaphragm-electret microphone. The RE90P-12 and RE90P-18 are mechanically designed for quick, easy mounting to a lectern, pulpit or podium equipped with a bulkhead female XLR-type 3-pin receptacle. Electro-Voice Wired Microphones are guaranteed against malfunction from any cause for two (2) years from the date of original purchase. In addition, the Limited Warranty for the acoustic system contained in these microphones shall apply for the life of the product, defined as a period of ten (10) years from the date that the manufacture of the specific microphone has been discontinued. Any and all active electronics incorporated in these microphones are guaranteed against malfunction due to defects in materials or workmanship for a period of three (3) years from the date of original purchase. The Limited Warranty does not extend to cables, cable connectors, or switches. Additional details are included in the Uniform Limited Warranty statement. For warranty repair, service information, or a listing of the repair facilities nearest you, contact the service repair department at: 616/695-6831 or 800/685-2606. For technical assistance, contact Technical Support at 800/234-6831 or 616/695-6831, M-F, 8:00 a. m. Specifications subject to change without notice. RE90P-12 and RE90P-18 Condenser Cardioid Gooseneck Microphones 2 The Electro-Voice CPSM shock mount effectively isolates the mounted RE90P-12 and RE90P-18 podium microphones from shock-induced vibrations that would be experienced on podiums, pulpits, table and desk tops, plus it provides theft-resistant security. Compared to hard mounting, the CPSM shock mount provides 15 dB (over 5 times) of shock isolation at 200 Hz. FMK FLANGE-MOUNT KIT For installations which do not require a shock mount, the FMK flange mount is designed for quick installation on podiums, pulpits, table and desk tops and provides theft-resistant security. [. . . ] Compared to hard mounting, the CPSM shock mount provides 15 dB (over 5 times) of shock isolation at 200 Hz. FMK FLANGE-MOUNT KIT For installations which do not require a shock mount, the FMK flange mount is designed for quick installation on podiums, pulpits, table and desk tops and provides theft-resistant security. Architects' and Engineers' Specifications RE90P-12 The microphone shall be a single-D cardioid back-electret condenser type with frequency response of 100 to 15, 000 Hz. The microphone shall have a 200-ohm nominal balanced output, with an output level of ­43. 0 dB (0 dB = 1 mW/pascal). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE BB4

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE BB4 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag