User manual ELECTRO-VOICE CM-1 EDS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE CM-1 EDS. We hope that this ELECTRO-VOICE CM-1 EDS user guide will be useful to you.
Lastmanuals help download the user guide ELECTRO-VOICE CM-1 EDS.
Manual abstract: user guide ELECTRO-VOICE CM-1 EDS
Detailed instructions for use are in the User's Guide.
[. . . ] CM-1
CobraNetTM Interface Module
· 100BASE-TX Ethernet Interface 100Mbit/s full-duplex Ethernet Interface; IEEE 802. 3u compatible. [. . . ] Status LEDs Link, Activity, Fault and CobraNetTM Conductor status indication via Ethernet connectors.
· · · ·
CobraNetTM is a network technology for multichannel transmission of digital audio data. The CM1 is a compact interface module for connection to a CobraNetTM network allowing the simultaneous transmission of up to 32 digital audio input signals and 32 digital audio output signals.
Supply Voltage / Current 3. 3 V DC, ±0. 3 V / 1. 2 A 5 V DC, ±0. 25 V / 0. 1 A Ethernet Connectors RJ-45, integrated transformer (Primary / Secondary) isolation, IEEE 802. 3u Standard Sample Rate 48 kHz Data Format 16 / 20 / 24 Bit Operating Temperature Range 0 °C . . . 40 °C Dimensions (W x H x D) 89mm x 27mm x 92mm 3. 50" x 1. 06" x 3. 62" Weight 75 g (0. 17 lb)
Yellow: Interface in use Blinking: Device is a CobraNetTM Conductor Green: Link okay Blinking: Communication active Fatal Error: Yellow LEDs on both sockets flashing
POWER SUPPLY +3. 3V +5V 24. 576 MHz
CM-1 Block Diagram
HOST / SERIAL
MAC SRAM FLASH
COBRANET INTERFACE PHY
AUDIO IN AUDIO OUT
4 x 8 Channels
4 x 8 Channels
1. Remove cover plate (6 screws on the sides, 3 screws on top, 4 screws on the rear) 3. Install the CM-1 module (see picture); first, secure it with 2 screws on the rear panel (A), then with 2 screws on the bolt (B), tighten the screws 5. Make the following cable connections: - J1 on CM-1 module with CN28 on main board 80500 (65mm flat wire cable) (C) - J3 on CM-1 module with CN5 on DSP-Board 80496 (190mm flat wire cable) (D) 6. [. . . ] For customer orders, contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 736-4212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE CM-1 EDS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE CM-1 EDS will begin.