User manual ELECTRO-VOICE DS30 DATASHEET

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE DS30. We hope that this ELECTRO-VOICE DS30 user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE DS30.


Mode d'emploi ELECTRO-VOICE DS30
Download
Manual abstract: user guide ELECTRO-VOICE DS30DATASHEET

Detailed instructions for use are in the User's Guide.

[. . . ] Sound pressure level will be 105 dB (1 W/1 M) with a 500-5, 000-Hz pink noise signal applied, and the horn will produce a horizontal beamwidth of 150° and a vertical beamwidth of 110° at 2 kHz. The horizontal coverage shall be constant over the frequency range of 3 kHz to 10 kHz. The loudspeaker shall be compression-molded fiberglass capable of satisfactory mechanical performance in the temperature range from -40°C to +40°C and not subject to sunlight embrittlement. Other major external speaker parts shall be die-cast zinc and finished in gray polyester paint to match the molded horn parts. [. . . ] All components shall be resistant to damage from weather, moisture and fungus. A steel swivel bracket capable of providing either vertical or horizontal installation and a variety of adjustments, is provided. The loudspeaker shall be 52. 0 cm (20. 5 in. ) high, 26. 5 cm (10. 5 in. ) wide and 54. 6 cm (21. 5 in. ) long. The loudspeaker shall be the 848AT, which includes a 70V/25V transformer and weighs no more than 7. 0 kg (15. 5 lb). Specifications: Frequency Response: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260-10, 000 Hz ±5 dB (see Figure 3) Power Handling, 8 Hours, 6 dB Crest Factor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 watts (500-5, 000 Hz pink noise) Transformer Taps and Impedances: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Table 1 Sound Pressure Level at 1 Meter 1 Watt Input Averaged, Pink Noise Band-Limited from 500-5, 000 Hz: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 dB Horizontal Beamwidth: 150° at 2 kHz (see Figure 2) Vertical Beamwidth: 110° at 2 kHz (see Figure 2) Directivity Factor R (Q): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. 4 @ 2 kHz Usable Low-Frequency Limit: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Errors attributable to the slight differences between the geometric and acoustic apexes are reduced to an inconsequential level by the relatively long, 20-foot measuring distance. The horn was suspended freely with no baffle. The polar plots shown in Figure 1 display the results of those tests. The center frequency is noted on each plot. The wider plot on each chart is the horizontal polar (-) and the narrower plot is the vertical polar (---). Transformer A transformer is installed in the driver housing. Power taps for the transformer are listed in Table 1. Low-Frequency Driver Protection When frequencies below the low-frequency cutoff for the horn assembly are fed to the driver, excessive current may be drawn by the driver. For protection of the driver, amplifier and transformer, capacitor(s) in series with driver or transformer primary is recommended. Values for other frequencies can be determined by using the formula: C200 = Values shown in the following table C200 x 200 C= f f = New Frequency [ ] Table 1. Series Protection Capacitors for 200 Hz and Below . [. . . ] Values for other frequencies can be determined by using the formula: C200 = Values shown in the following table C200 x 200 C= f f = New Frequency [ ] Table 1. Series Protection Capacitors for 200 Hz and Below . Power 30 W 15 W 8W 4W 2W 1W 1/2 W 166 333 625 1250 70-Volt Lines Impedance Capacitance 5 mf 2 mf 1 mf 0. 5 mf 156 312 625 1250 70-Volt Lines Impedance Capacitance 5 mf 2 mf 1 mf . 5 mf Figure 2 848AT Beamwidth vs. Frequency Figure 1 848AT Polar Response Figure 3 848AT Frequency Response (1 watt at 1 meter) USA Canada Switzerland Germany France Australia Hong Kong Japan Singapore Mexico UK Africa, Mid-East Latin America 12000 Portland Ave South, Burnsville, MN 55337, Phone: 952-884-4051, FAX: 952-884-0043 705 Progress Avenue, Unit 46, Scarborough, Ontario, Canada, M1H2X1, Phone: 416-431-4975, 800-881-1685, FAX: 416-431-4588 Keltenstrasse 11, CH-2563 IPSACH, Switzerland, Phone: 41/32-331-6833. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE DS30

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE DS30 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag