User manual ELECTRO-VOICE ELX215

[. . . ] 12 Frequency Response Graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Live X Model Reference Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Secure cables with wire ties or tape whenever possible. See Figures 1a and 1b for optimal coverage areas in front of the loudspeaker when in monitor position. Figure 1a: ELX112 / ELX115 Optimum Coverage (Front View) Figure 1b: ELX112 / ELX115 Optimum Coverage (Side View) Electro-Voice Live X Series Passive Owner's Manual 5 Tripod and Floor Monitor Operation Tripod Electro-Voice ELX112 and ELX115 loudspeakers include 35mm (1-3/8") stand mounts to allow mounting on tripod stands or above an ELX118. Make sure to: · Check the specifications of the speaker stand to be certain it is capable of supporting the weight of the speaker. · Check that the speaker stand is placed on a flat, stable surface and be sure to fully extend the legs of the stand. Do not try to make the stand "taller" and compromise its structural integrity. · Route cables and position the stand so that performers, production crew and audience members will not trip over the stand or cables and pull the speaker system over. Secure cables with wire ties or tape whenever possible. · Do not attempt to suspend more than one speaker on a stand designed for a single speaker. · Unless you are confident that you can safely handle lifting the weight of the speaker onto the stand, ask another person to help you place it. Figure 2a: ELX112 / ELX115 on Tripod Stand 6 Figure 2b: Live X Full-Range/Sub Stack with Pole Mount Electro-Voice Live X Series Passive Owner's Manual Recommended Configurations Basic Stereo System using ELX112's or ELX115's NL4 Pin Configuration Pins 1+ and 1Pins 2+ and 2Used Not Used Amplifier Load (per Output Channel) # of Speakers 1 2 3 4 Nominal 8 Ohms 4 Ohms 2. 7 Ohms 2 Ohms Minimum 7 Ohms 3. 5 Ohms 2. 3 Ohms 1. 8 Ohms ELX112 or ELX115 ELX112 or ELX115 Caution: Do not exceed the maximum load rating of the amplifier. 45 Hz low pass filter (from mixer or processor) Output B Output A Q66 Amplifier Input B Input A Mixer Electro-Voice Live X Series Passive Owner's Manual 7 Recommended Configurations (cont') Linking ELX118 subwoofers to ELX112's or ELX115's This configuration allows a user to increase the low frequency performance without using additional amplifier channels. ELX112 or ELX115 NL4 Pin Configuration Pins 1+ and 1Pins 2+ and 2Used Not Used ELX112 or ELX115 Amplifier Load (per Output Channel) # of Subwoofer/ Full-Range Combinations 1 2 Nominal Minimum 6 Ohms 3 Ohms 4. 2 Ohms 2. 1 Ohms Caution: Do not exceed the maximum load rating of the amplifier. ELX118 ELX118 Output B Output A Input A Q66 Amplifier 30 Hz low pass filter (from mixer or processor) 8 Mixer Electro-Voice Live X Series Passive Owner's Manual Input B Recommended Configurations (cont') Basic Stereo System using ELX215's NL4 Pin Configuration Pins 1+ and 1Pins 2+ and 2Used Not Used ELX215 ELX215 Amplifier Load (per Output Channel) # of Speakers 1 2 Nominal 4 Ohms 2 Ohms Minimum 3. 7 Ohms 1. 9 Ohms Caution: Do not exceed the maximum load rating of the amplifier. Output B Output A Q66 Amplifier Input A 35 Hz low pass filter (from mixer or processor) Mixer Electro-Voice Live X Series Passive Owner's Manual Input B 9 Recommended Configurations (cont') Using multiple ELX112's or ELX115's as stage monitors ELX112's or ELX115's (Monitor Position) Output B Output A Q66 Amplifier Amplifier Load (per Output Channel) # of Speakers 1 2 3 4 Nominal 8 Ohms 4 Ohms 2. 7 Ohms 2 Ohms Minimum 7 Ohms 3. 5 Ohms 2. 3 Ohms 1. 8 Ohms Input B Mixer 45 Hz low pass filter (from mixer or processor) Input A NL4 Pin Configuration Pins 1+ and 1Pins 2+ and 2Used Not Used Caution: Do not exceed the maximum load rating of the amplifier. 10 Electro-Voice Live X Series Passive Owner's Manual Specifications (Part Number) Model (F01U170823) ELX1 2 1 (F01U170824) ELX1 15 (F01U170826) ELX215 (F01U170825) ELX1 18 Freq. Measured SPL : 3 82 Hz - 18 kHz1 55 Hz - 20 kHz1 94 dB 132 dB 45 Hz 75 Hz - 18 kHz1 50 Hz - 20 kHz1 95 dB 134 dB 40 Hz 90° x 50° 62 Hz - 18 kHz1 38 Hz - 20 kHz1 96 dB 137 dB 35 Hz 50 Hz - 100 Hz2 35 Hz - 200 Hz2 96 dB 134 dB 30 Hz Omnidirectional Recommended HP Freq. : Coverage (Horiz. F01U170823 F01U170824 F01U170825 F01U170826 Warranty Information Visit www. electrovoice. com/warranty for warranty information. 14 Electro-Voice Live X Series Passive Owner's Manual Impedance (Ohms) Sensitivity (dB) Sensitivity (dB) Impedance (Ohms) Sensitivity (dB) Sensitivity (dB) Troubleshooting Problem 1. No Sound Possible Cause(s) Amplifier Action Connect a known working test speaker to the amplifier outputs. If there is no sound, check that all the electronics are on, the signal routing is correct, the source is active, the volume is turned up, and so on. [. . . ] Check and correct the system grounding, as required. Wiring 2. Poor Low Frequency Response Speakers wired out-of-polarity 3. [. . . ]