User manual ELECTRO-VOICE EVID 12.1P

[. . . ] EVID 12. 1P User Manual Electro-Voice® EVID 12. 1P User Manual Table of Contents Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Feature Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Step-by-Step Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Straighten the EV® logo and press firmly at its center to seat it securely into its mounting hole. 1 1 Rungs 2 3 Rungs 3 2 This side towards wall Figure 8: Corner Mounting Figure 9: Midwall Mounting For midwall mounting Attach the four rubber mounting feet inside the corners on the side of the enclosure that will be against the wall and attach the safety line to the eyebolt. Insert one of the 3/8-16-thread Phillips-head screws through the remaining clip and keep it within arms reach. Lift the enclosure up to the ceiling and bring its back into contact with the bracket rungs. Slide the enclosure sideways to engage the clip over one bracket rung (1) and, while holding it tight against both rungs, insert the 3/8-16-thread screw with its clip into the remaining mounting hole so the clip engages the remaining bracket rung (2, 3). Finger-tighten the screw and straighten the clip. It will slide down the rungs until the four rubber feet are snug against the wall. Using a #3 right-angle Phillips screwdriver, securely tighten the second Phillips-head screw. Gently rotate the EV® logo a quarter turn and press firmly at its center to seat it securely into its mounting hole. See Figure 9. Electro-Voice® EVID 12. 1P User Manual 5 Mounting through a suspended ceiling grid On the rear of the enclosure install and tighten two 3/8-16-thread forged steel eyebolts (one is included) with a 3/8" flat washer under each. Cut two pieces of ordinary drop ceiling L angle (wall track) 23 3/4" long and screw them to the top and bottom of the enclosure with 3/4"-long sheet metal screws, as shown in Figure 10. Connect all of the wires and suspend the enclosure, face down, by the eyebolts in accordance with accepted safe rigging practice. Adjust the length of the rigging cables so the tips of the installed L angles just rest on the ceiling cross-tees. This stabilizes the enclosure from rocking. Trim the ceiling panel to fit the new opening(s) and drop into place. It is the installers responsibility to assure that the chosen rigging points are strong enough to support the load. Warning: Never try to install this speaker in a suspended ceiling without proper rigging support! Rigging cables L angle Eyebolts Ceiling tile Acoustic port Figure 10: Attach L Angles to Speaker Floor Mounting The EVID 12. 1P may be placed directly on the floor in a corner or on its side along a straight wall by simply attaching the four rubber mounting feet to the side that will sit on the floor. Step 5: Test System Operation After all connections are made test the complete system operation. Appendix C on page 10 contains a troubleshooting guide to assist in locating a variety of speaker related problems. 6 Electro-Voice® EVID 12. 1P User Manual Safety Agency Compliance The EVID 12. 1P bracket system has successfully passed EIA 636 at a safety factor of 6:1. The bracket system is intended to support the EVID 12. 1P only. Never set anything on, or hang anything from, the EVID 12. 1P enclosure when using this bracket. For a copy of the model-specific CE Declaration of Conformity, contact Electro-Voice at the address listed at the end of this manual. Maintenance Your EVID system has been designed and manufactured to provide years of durability and reliable service. Units may be cleaned by wiping with a soft, damp cloth. Never use solvents or harsh cleaning agents of any kind. Appendix A: Warranty Statement Electro-Voice® Speakers and Speaker Systems are guaranteed against malfunction due to defects in materials or workmanship for a period of five (5) years from the date of original purchase. [. . . ] Replace the hatch cover and tighten the four screws. Locate the small center hole, properly orient the EV® logo, and press it firmly into place at its center to reseat it in the mounting hole. · · · · 10 Electro-Voice® EVID 12. 1P User Manual Appendix D: Troubleshooting Guide Problem 1. No sound Possible Cause(s) Action Amplifier Verify that that the line level signal cables XLR connector has been pushed all the way into the Low Level In jack on the amplifier panel. Turn the Power switch on and the volume up until you can hear sound emitting from the 12. 1p subwoofer. [. . . ]