User manual ELECTRO-VOICE FMR-500

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE FMR-500. We hope that this ELECTRO-VOICE FMR-500 user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE FMR-500.

ELECTRO-VOICE FMR-500 : Download the complete user guide (698 Ko)

Manual abstract: user guide ELECTRO-VOICE FMR-500

Detailed instructions for use are in the User's Guide.

[. . . ] Telex R Operating Instructions FMR-500 User Guide Section 1 - Quick Set-Up Quick Set-up: Receiver 1. Plug the power supply into the back of the receiver and into an outlet. P r es s a n d h o l d th e S ET b u t t o n u n t i l ClearScanTM shows and starts flashing on the right side of the screen. When ClearScan stops flashing, the receiver will automatically set itself and display the clearest group and channel. [. . . ] If the meter peaks all the way to the right or well below the -3dB level, adjust the transmitter audio gain. To adjust the transmitter gain, gently insert the provided screwdriver (or other 3/32 - 2. 5 mm screwdriver) into the adjustment hole above the display screen. Turn lightly until the screwdriver tip goes into the adjustment level control Gently turn counterclockwise until the control stops (the microphone output is at minimum but not off). Slowly turn the gain control up (clockwise) while speaking/singing into the microphone and audiometer shows peaks around -3 dB. NOTE: Operating with the transmitter audio gain set as high as possible (without distortion or peaks all the way to the right end of the meter) will result in the best performance and highest signal to noise ratio. Receiver Setup and Operation - Step 9 to complete system set up and test. 5 Bodypack Transmitter - WT-500 1 SET 6 Telex R 9 UHF WIRELESS 755050 GP CH 5 Figure 8 Control View 4 8 Figure 7 Bodypack Transmitter 23 WT-500 Controls, Connectors, and Indicators 1. LCD Display (Channel, Frequency or Battery Level Indication) Figure 9 Top View 6. Audio Gain Adjustment -6- Bodypack Transmitter Setup and Operation 1. With battery compartment still open, turn the unit on with Power switch on the top panel. The battery low LED will light for a second and the display will show the Group and Channel numbers. Change the group and channel numbers to match those displayed on the receiver by pressing SET. Once the desired Group number is showing, press SET to select and the Channel number will flash. Select the Channel and press SET again, the flashing will stop and the channel is now set. By pressing and holding the UP and DOWN arrow keys together for 3 seconds, the SET key is disabled. To reactivate the SET key, simply press and hold the UP and DOWN keys again for 3 seconds. With the transmitter and receiver on and matching Group and Channel, the main receiver display should be indicating a RF signal on the bar graph. If the level meter does not show reception, make sure the channels are matching and refer to the trouble shooting section. Microphone: Plug the microphone cable into the top panel of the WT-500. Speak into the microphone and the Audio Meter bar graph should indicate audio signal presence. Guitar: Turn off the bodypack, press and hold SET while you turn the bodypack on. A guitar symbol will appear in the display to indicate instrument mode. Strum the guitar and the Audio Meter bar graph on the receiver should indicate audio signal presence. The transmitter audio gain is factory set at the middle of the range, which should be suitable for most applications. [. . . ] A Band 648 - 676 MHz (TV Channels 43 - 48) B Band 696 - 724 MHz (TV Channels 54 - 56) Number of Channels . >1122 possible frequencies Programmable in 25 kHz steps Modulation . D 43. 69 mm H x 190. 50 mm W x 150 mm D Audio Parameters Frequency Response . (max @ 40 kHz deviation) 330mV RMS 100K OHM Load, Mic Position 10mV to 2V RMS 100K OHM Load, Line Position Unbalanced Output . [. . . ]


Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE FMR-500 will begin.

Search for a user manual


Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.