User manual ELECTRO-VOICE PHOENIX BROCHURE

[. . . ] More drivers means higher power handling capacity and more SPL per horn, allowing the use of less overall cabinets for the same output. Dual drivers offer the benefit of tremendous headroom in the mid and high frequencies letting you confidently push that vocal up and over the top of a dense mix or high stage volumes. Additionally, dual drivers don't have to work as hard as a single driver which results in less heat build up in each driver and provides reliable roadworthy longevity. [. . . ] Dual high-efficiency, forced-air cooled DVX3121 12-inch woofers compliment the high performance manifold section of the PX2122. With an overall broadband sensitivity of 102dB and "biamp only" architecture, the PX2122 is ready to be utilized to its maximum high power potential. The PX2122 employs rugged EVCOAT® covering and 18-mm, 13-ply plywood with complex tongue-in-groove construction for long-term strength and consistency. Handles on the top, bottom and both sides make transport easy, while eight M10 points provide flexibility in situations where hanging is either necessary or optimal. accessory: Optional PX-D1 wheel kit for PX2122 and PX2152 rotates to a horizontal position for rolling and a vertical position when forming arrays, eliminating the need to remove and store the PX-D1 during use. Whether combined with the PX2181 subwoofer or used as a standalone system, the PX2152 shines in medium throw applications that require the low-frequency reproduction of 15-inch woofers. Accurately summed dual ND2 compression drivers in a manifold configuration allow for increased power handling, mid and highfrequency headroom, and low distortion. Selectable bi-amp or passive operation makes the PX2152 work extremely well in conjunction with Phoenix subwoofers or as a single box system for live and club sound. The wider 60° x 45° coverage pattern of the low distortion rotate-able horn gives the PX2152 added flexibility in system design. With an integral 15° per side trapezoidal angle, two PX2152 can be arrayed for a larger system; simply use one cabinet for a smaller system. In an effort to simplify setup, PX2152 cabinets can be securely splayed within the safety grooves routed into the PX2181 subwoofer, reducing the need for straps and eliminating speaker cluster guesswork. Dual high-efficiency, forced-air cooled DVX3150 15-inch woofers compliment the high performance manifold section of the PX2152. With an overall broadband sensitivity of 99dB and the ability to run full range passive or bi-amp, the PX2152 is an outstanding solution for a wide variety of applications. The PX2152 employs rugged EVCOAT® covering and 18-mm, 13-ply plywood with complex tongue and groove construction for long-term strength and consistency. Handles on the top, bottom and both sides make transport easy, while eight M10 points provide flexibility in situations where hanging is either necessary or optimal. accessories: Optional durable covers for Phoenix systems resist the normal wear and tear of the road. Shown from left - PXC-Sub, PXC-Top, PXC-15M and PXC-12M. The PX2181 is a high-efficiency horn-loaded dual 18-inch subwoofer intended for high-output low-frequency sound reinforcement. With the ability to perform in either portable or fixed installation applications, the flexibility of the PX2181 makes it usable within a Phoenix system, a club installation, or as an add-on to much larger concert touring systems. Designed to be placed in vertical and horizontal orientations, alignment cups are placed in the PX2181 enclosure to secure multiple subwoofers in an array. Up to three Phoenix top boxes can be safely placed within the unique grooves routed into two sides of the PX2181 in the horizontal position, while routed foot receptacles securely maintain a single Phoenix top box in the vertical position. A switch allows the user to toggle between parallel mode (in which both woofers can be addressed by one amplifier channel) and dual mode (where each woofer can be addressed independently). [. . . ] (50mm) Diaphragm Compression Drivers 1400 Hz 8 Ohms Nominal 8 Ohms Nominal (3) Neutrik Speakon NL4 18mm Plywood, Black EVCoatTM Rigging Point for VSA-1 Strong Arm Accessory Power Handling (System) Bi-amp only LF Power Handling (Bi-amp): HF Power Handling (Bi-Amp) LF Transducer: HF Transducers Crossover Frequency LF Impedance HF Impedance Connectors Enclosure Material Suspension Grille Dim (H x W x D) Net Weight Shipping Weight 1 1000W Continuous, 4000W Peak 80W Continuous, 320W Peak (2) DVX3121, 12 in. (50mm) Diaphragm Compression Drivers 1600 Hz 4 Ohms Nominal 8 Ohms Nominal (2) Neutrik Speakon NL4 18mm Plywood, Black EVCoatTM (8) M10 Points - (6) on Top and (2) on Bottom of Enclosure Polyester Powder Coated, 16GA Polyester Powder Coated, 16GA Galvanized Steel, Rotatable Logo Galvanized Steel, Rotatable Logo 1219mm x 457mm x 445mm (48. 00" x 18. 00" x 17. 50") 50. 1 kg (110. 3 lbs) 58. 9 kg (129. 6 lbs) 1219mm x 457mm x 445mm (48. 00" x 18. 00" x 17. 50") 50. 76 kg (111. 9 lbs) 60. 51 kg (133. 4 lbs) Polyester Powder Coated, 16GA Polyester Powder Coated, 16GA Galvanized Steel, Rotatable Logo Galvanized Steel, Rotatable Logo 546mm x 366mm x 305mm (21. 50" x 14. 42" x 12. 04") 2 3. 04 kg (50. 8 lbs) 2 6. 14 kg (57. 6 lbs) 610mm x 442mm x 329mm (24. 00" x 17. 42" x 12. 97") 2 5. 1 kg (55. 3 lbs) 2 8. 2 kg (62. 1 lbs) Half Space measurement Available Accessories: PX-D1 - wheel kit for PX2122 and PX2152 PX-D2 - wheel kit for PX2181 PX-G1 - fly grid for PX2122 and PX2152 VSA-1 - strong arm mount for PX1122M and PX1152M TCA-1 - truss clamp for VSA-1 EBK-M10 - set of three M10 eyebolts PXC-12M - durable Cordura cover for PX1122M PXC-15M - durable Cordura cover for PX1152M PXC-Top - durable Cordura cover for PX2122 and PX2152 PXC-Sub - durable Cordura cover for PX2181 Americas­Headquarter Americas Telex Communications Inc. 12000 Portland Ave South, Burnsville, MN 55337, USA USA­Ph: 1-800-392-3497 Fax: 1-800-955-6831 Canada­Ph: 1-866-505-5551 Fax: 1-866-336-8467 Latin America­Ph: 1-952-887-5532 Fax: 1-952-736-4212 Europe, Africa & Middle-East Headquarter EAME EVI Audio GmbH Hirschberger Ring 45, D-94315, Straubing, Germany Phone: +49 9421 706-0, Fax: +49 9421 706-265 France: EVI Audio France S. A. , Parc de Courcerin, Allée Lech Walesa, F 77185 Lognes, France Phone: +33 1-6480-0090 Fax: +33 1-6006-5103 UK: Shuttlesound, 4 The Willows Centre, Willow Lane, Mitcham, Surrey CR4 4NX, UK Phone: +44 208 646 7114 Fax: +44 208 254 5666 Asia & Pacific Rim­Headquarter Asia Singapore: Telex Pte. [. . . ]