User manual ELECTRO-VOICE PROANNOUNCE

[. . . ] ProAnnounce System Reference Manual DISCLAIMER & COPYRIGHT The material and instructions covered in the document are subject to change without notice. does not guarantee the suitability of the material in this document for your particular application. Copyright © 2003 Telex Communications, Inc. All rights reserved. Page ii ProAnnounce System User Handbook 1. 1 1. [. . . ] The selection keys are used in this mode to assign a program (background music) to the desired areas or groups. The PROGRAM LED lights while being in the program assign mode. In this case the selection LED's indicate the areas / groups the program is being transmitted into. Keeping this key pressed and simultaneously pressing the STOP key selects the setup-mode and the PROGRAM LED starts blinking. Now you can alter preferences or make other changes as described in the chapter 5. 2. 7 Paging Station Configuration In Setup Mode. When in setup-mode, this key is used to select the following parameter (parameter selection). 10 ALARM key and Indicator Pressing the ALARM key starts an alarm signal that is transmitted into all areas. The alarm indicator lights when launching an alarm. Pressing the STOP key or subsequently pressing the ALARM key terminates the alarm signal. What kind of alarm signal is being transmitted is defined during the configuration procedure of the ProAnnounce system. 11 Optional Key-Slots These slots allow retrofitting an additional covered key and a key-locked switch. The front panel is already prepared for the installation of two 18 mm pushbuttons / switches. You only have to cut suitable holes into the front panel foil. Internal fittings and cables are also already prepared. The newly installed switches' functions are assigned during the configuration procedure via PC; e. g. : second alarm-pushbutton for transmitting an alarm signal into specific areas (selective alarm), or assigning the system ON / OFF function to the key-locked switch. Detailed information and installation instructions are provided in the chapter 5. 2. 13 Optionally Available Accessories. ProAnnounce System User Handbook 1. 1 Page 43 12 Microphone After pressing the TALK button and after the BUSY LED lights making announcements in pre-selected areas or groups is possible using the integrated gooseneck microphone. The optimum distance from the microphone is approximately 20 to 35 cm. The microphone pre-amplifier embodies a limiter to control signal peaks and protect the system against overdrive. The extension socket (EXT) allows connecting a second microphone with TALK button. Assigning the function (area, group) of the external microphone is performed during the configuration via PC. 13 Display Depending on the actual operational status of the system, the LC-display with 2 lines of 16 characters each, shows information on time, operation mode, user notes, setting up, fault messages including precise device / module specification, etc. 5. 2. 4 1 LAN socket Connections This is the interface for connecting DPC 4000 Series paging stations to the ProAnnounce system. The 8-pole RJ45 connector provides power supply, control interface RS-485, and audio connections. [. . . ] 5. branch off the DCS 401 card, disconnect the flat ribbon cables and dismantle the card. transfer address adjustments from the old card to the new one integrate and connect the new card, restore power supply carry out the netscan with the PROANNOUNCE designer and start fastsave (both the green and red LED must be on permanently) 6. 4. 5 DCS 401 "R" series controller: 1. disconnect the system from power supply screw off the DCS 401 R card and pull it out of the corresponding frame transfer address adjustments from the old card to the new one integrate and connect new card, restore power supply carry out the netscan with the PROANNOUNCE designer and start fastsave (both the green and red LED must be permanently on; the yellow status-LED must blink periodically) 6. 4. 6 DCS modules 408, 409, 412, 416: 1. disconnect the system from power supply branch off the DCS card, disconnect the xxx lines and dismantle the card transfer the jumper configuration completely to the new card integrate and connect new card, restore power supply both the green and the red LED on the DCS 401 must be permanently on now, otherwise, carry out the netscan with the PROANNOUNCE designer and start fastsave 6. 4. 7 DCS "R" ­ Modules 408 R, 409 R, 412 R, 416 R: 1. [. . . ]